PREVOST X3-45 COMMUTER Скачать руководство пользователя страница 431

Страница: 431 / 549

SECTION 18: BODY

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)

5.00 *

Finition Joint

Install a protective tape onto the tubing above welding

Apply Sika 205

Use a plastic spatula inside a Chix cloth to ensure
that Sika 205 reaches as far as the corner.

See PR000001 section B.

Apply Sika 252 black at the junction of both tubing.

Smooth down the joint

Remove protective tape

15.7.2 SIDE

CREST

FIGURE 50: SIDE CREST POSITIONING

18639



Clean vehicle surface using anti-silicone where the side crest and stickers will be applied.



Using hands apply and compress side crest.



Apply required stickers.

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Бренды по названию

Популярные бренды