PREVOST X3-45 COMMUTER страница 399 Скачать руководство пользователя

Страница: 399 / 549

SECTION 18: BODY

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)



Apply an even coat of Sika 255 onto the

door frame.



Position body panel onto door frame and

compress with your hands. Use a ruler.



Check body panel flatness using a 2-foot

ruler (must be within 2mm).



Check proper power window sliding inside

window frame.



If applicable, remove excess of Sika

adhesive all around door frame using Sika
208.



From the inside of the door, apply some

Sika 221 between door body panel and
frame and on welding spots as per figure.



Apply some #680066 glue inside fiber

glass groove and fix power window wiper.

NOTE

Anti-friction side must be on glass side.

RULER

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

Популярные бренды

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

Популярные бренды