PREVOST X3-45 COMMUTER Скачать руководство пользователя

Страница: 529 / 549

SECTION 23: ACCESSORIES

DOB 2490-2789 | X3-45 Commuter PA1605 Maintenance Manual (Final Version – Rev.2 April 2016)

FIGURE 11: WIPER ARMS POSITIONING

23253

3.4 TROUBLESHOOTING

SYMPTOM

PROBABLE CAUSE

REMEDY

FAIL TO SPRAY WASHER

FLUID

A. Reservoir

empty.

B. If below 32



F (0



C), improper

washer fluid frozen.

C. Contamination in tubing or

nozzles.

D. Tubing

damage.

E. Tubing bent (kinked) or off one

or more connections.

A. Add proper fluid

B. Store coach or parts in heated

area, then purge system with low-
temperature solution.

C. Remove with compressed air, if

severely clogged, replace items.

D. Replace

section.

E. Realign tubing and/or refit. Trim

end to ensure proper fit or replace.

INADEQUATE SPRAYING

A. Tubing failure.

A. Replace tubing.

SLOW OPERATION

A. Improper

solution.

B. Jet stream improperly directed.

C. Check if valve is stuck in the

open position.

A. Replace with proper type solution.

B. Reposition

nozzles.

C. Remove, clean or replace.

Содержание X3-45 COMMUTER






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

Популярные бренды

PREVOST X3-45 COMMUTER, Руководство по обслуживанию

Результаты поиска

Содержание X3-45 COMMUTER

Отзывы:

Похожие инструкции для X3-45 COMMUTER

Бренды по названию

Популярные бренды