Panasonic ZEQUO 6400 Скачать руководство пользователя страница 496 | Manualshive

Страница: 496 / 1058

background image

46. LLDP Commands

497

46.LLDP Commands

LLDP (Link Layer Discovery Protocol) is a function to periodically collect

connected device information. If devices, such as an IP phone, printer, and

network camera, support LLDP, you can learn what devices are connected where.

This function also allows you to identify configuration errors based on collected

information and change the protocol settings or Switching Hub operations

according to the information.

Figure 46-1 LLDP overview

enable lldp
disable lldp
config lldp [message_tx_interval <sec 5-32768> | message_tx_hold_multiplier <int 2-10> |

tx_delay <sec 1-8192> | reinit_delay <sec 1-10>]

show lldp
config lldp forward_message [enable | disable]
config lldp notification_interval <sec 5-3600>
config lldp ports [<portlist> | all] [notification [enable | disable] | admin_status [tx_only | rx_only |

tx_and_rx | disable] | mgt_addr [ipv4 <ipaddr> | ipv6 <ipv6addr>] [enable | disable] |
basic_tlvs [{all} | {port_description | system_name | system_description |
system_capabilities}] [enable | disable] | dot1_tlv_pvid [enable | disable] |
dot1_tlv_protocol_vid [vlan [all | <vlan_name 32>] | vlanid <vidlist>] [enable | disable] |
dot1_tlv_vlan_name [vlan [all | <vlan_name 32>] | vlanid <vidlist>] [enable | disable] |
dot1_tlv_protocol_identity [all | {eapol | lacp | gvrp | stp}] [enable | disable] | dot3_tlvs
[{all} | {mac_phy_configuration_status | link_aggregation | maximum_frame_size}] [enable
| disable]]

show lldp ports {<portlist>}
config lldp_med fast_start repeat_count <value 1-10>
config lldp_med log state [enable | disable]
config lldp_med notification topo_change ports [<portlist> | all] state [enable | disable]

«
...
494
495
496
497
498
...
»

Содержание ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZEQUO 6400

Бренд: Harman Kardon Страницы: 2

8271 Nways Ethernet LAN Switch

Бренд: IBM Страницы: 210

Бренд: GALCO Страницы: 22

PFS4226-24ET-240

Бренд: Dahua Страницы: 3

FlexFabric 5940 Series

Бренд: Hewlett Packard Enterprise Страницы: 123

Бренд: Icy Box Страницы: 10

Бренд: hager Страницы: 3

Hi-Speed USB 2.0 Hub

Бренд: Saitek Страницы: 14

Бренд: DeLOCK Страницы: 26

Бренд: B&B Electronics Страницы: 2

Бренд: Kramer Страницы: 4

Бренд: MiLAN Страницы: 13

iMatrix H44H150

Бренд: infobit Страницы: 27

Бренд: Tekvox Страницы: 40

Бренд: Lutron Electronics Страницы: 2

Peripheral Sharer 2 to 1

Бренд: Black Box Страницы: 35

Бренд: Comprehensive Страницы: 6

Sun Network QDR InfiniBand Gateway Switch

Бренд: Oracle Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды