Panasonic ZEQUO 6400 Скачать руководство пользователя страница 171

Страница: 171 / 1058

13. Bootup Function Commands

172



Example

To show boot_file

13.2. config boot_up command



Description

This command is used to config the boot_up command.

The parameter "<pathname>" can specifies file on either SD card or flash.

Pathname of the boot up file will be recorded in the system after issue the

commands above. And the 2nd boot up files can be shown by command "show

boot_file".

When use "config firmware image <pathname> boot_up" or "config configuration

<pathname> boot_up" commands, will check the file indicated by <pathname> is

existed or valid for boot up. If the file is not existed or not valid for boot up,

executing command will be failed.

The 2

Bootup Firmware/Configuration will not be changed until using

command to configure it. That means it will not clear the 2

Bootup Firmware/

Configuration pathname when it is saved in SD card even though the SD card is

pushed out or insert SD card no this boot file or system is rebooted.

For 2

Bootup Firmware or 2

Bootup Configuration, the factory default boot

up file should be: /c:/runtime.rom, /c:/config.cfg.



Format

config firmware image <pathname> boot_up

config configuration <pathname> boot_up



Parameters

None.

Zxxx0:admin#show boot_file
Command: show boot_file

*1st Bootup Firmware    : /d:/sd_runtime.rom
*1st Bootup Configuration   : /d:/sd_config.cfg
    *Can not change 1st Bootup File

2nd Bootup Firmware : /c:/runtime.rom
2nd Bootup Configuration : /c:/config.cfg

Actual Bootup Firmware : /c:/runtime.rom
Actual Bootup Configuration : /c:/config.cfg

SD card: d drive, FLASH: c drive
Zxxx0:admin#

Содержание ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZEQUO 6400

Отзывы:

Похожие инструкции для ZEQUO 6400

Бренды по названию

Популярные бренды

Panasonic ZEQUO 6400, Руководство по эксплуатации

Результаты поиска

Содержание ZEQUO 6400

Отзывы:

Похожие инструкции для ZEQUO 6400

Бренды по названию

Популярные бренды