manualshive.com logo in svg

Panasonic ZEQUO 6400, Руководство по эксплуатации

"Panasonic ZEQUO 6400 - отличное устройство с высокими технологиями. На нашем сайте вы можете скачать операционное инструкция по эксплуатации бесплатно. Просто загрузите мануал с manualshive.com и начните пользоваться всеми преимуществами этого устройства."

Поделиться
Скачать
background image

12.  Basic IP Commands    

157

12.1. config ipif

Description

Configure the parameters for an L3 interface. For IPv4, only the system interface can             

be specified for the way to get the IP address. If the mode is set to BOOTP or DHCP,                  

then  the  IPv4  address  will  be  obtained  through  the  operation  of  protocols.  The            

manual configuration of the IP address will be of no use. If the mode is configured to                

BOOTP or DHCP first, and then the user configures IP address later, the mode will be               

changed to manual configured mode. For IPv6, multiple addresses can be defined on            

the  same  L3  interface.  For  IPv4,  multi-netting  must  be  done  by  creation  of  a             

secondary interface. Note that an IPv6 address is not allowed to be configured on a              

secondary interface.

Format

config ipif <ipif_name 12> [{ipaddress <network_address> | vlan <vlan_name 32> | 

state [enable | disable]} | bootp | dhcp | proxy_arp [enable | disable] {local [enable | 

disable]} | ipv6 [ipv6address <ipv6networkaddr> | state [enable | disable]] | ip_mtu 

<value 512-1712> | ipv4 state [enable | disable] | dhcpv6_client [enable | disable] | 

ip_directed_broadcast [enable | disable]]

Parameters

ipif

Specifies the IP interface configured.
<ipif_name 12>

Enter the name of the IP interface used here. This name can be up to 12 characters                
long. The default interface is 'System'.

ipaddress(Optional) The IP address and netmask of the IP interface to be created.

<network_address>

Specify  the  address  and  mask  information  using  the  traditional  format  (for          
example, 10.1.2.3/255.0.0.0 or in CIDR format, 10.1.2.3/8).

vlan

(Optional) The name of the VLAN corresponding to the IP interface.
<vlan_name 32>

Specify the VLAN name. The maximum length is 32 characters.

state

Enable or disable the IP interface.
enable

Enable the IP interface.

disable

Disable the IP interface.

bootp

Enable or disable the BOOTP client to get the IP address.

dhcp

Enable or disable the DHCP client to get the IP address.

proxy_arp

(Optional) Enable or disable the proxy ARP. This is for the IPv4 function. The default is               
disabled.
enable

Enable the proxy ARP.

disable

Disable the proxy ARP.

Содержание ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ZEQUO 6400

JDS Uniphase SCG Series User Manual preview
SCG Series
Бренд: JDS Uniphase Страницы: 37
Jasco AS2006 Manual preview
AS2006
Бренд: Jasco Страницы: 2
ADDER GEMAV2GEM Installation And Use Manual preview
GEMAV2GEM
Бренд: ADDER Страницы: 46
Lindy 32351 Manual preview
32351
Бренд: Lindy Страницы: 70
CYP CDPS-UA6H2HFS Operation Manual preview
CDPS-UA6H2HFS
Бренд: CYP Страницы: 32
Bühler technologies Nivotemp NT-EL Installation And Operation Instructions Manual preview
Nivotemp NT-EL
Бренд: Bühler technologies Страницы: 20
Alpha Cordex HP CXRF 48-2.4kW Manual preview
Cordex HP CXRF 48-2.4kW
Бренд: Alpha Страницы: 56
Atlona AT-HD-SC-500 Manual preview
AT-HD-SC-500
Бренд: Atlona Страницы: 22
CYP CMSI-4H4CV Operation Manual preview
CMSI-4H4CV
Бренд: CYP Страницы: 20
PCB Piezotronics 685B0001A13 Installation And Operating Manual preview
685B0001A13
Бренд: PCB Piezotronics Страницы: 31
Lantech LGS-2424C User Manual preview
LGS-2424C
Бренд: Lantech Страницы: 80
H3C FS5300-EI Series Compliance And Safety Manual preview
FS5300-EI Series
Бренд: H3C Страницы: 57
Videosec RF-ZE901-220 Installation Manual preview
RF-ZE901-220
Бренд: Videosec Страницы: 3
ATEN UC2322 User Manual preview
UC2322
Бренд: ATEN Страницы: 16
EKOBUY ekb10075 User Manual preview
ekb10075
Бренд: EKOBUY Страницы: 8
SALZ 4008GT Quick Installation Manual preview
4008GT
Бренд: SALZ Страницы: 2
Buffalo BS-GU2005 Hardware Manual preview
BS-GU2005
Бренд: Buffalo Страницы: 2
N-Tron 100-POE4 User Manual & Installation Manual preview
100-POE4
Бренд: N-Tron Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды