Panasonic ZEQUO 6400 Скачать руководство пользователя страница 15

Страница: 15 / 1058

1. Product Outline

1.5.

LED Behavior

1.5.1. LED Behavior at Starting-up

When you turn on this Switching Hub, all LEDs are lit momentarily. POWER LED lights

green and STATUS LED lights orange, and then the hardware self diagnosis is executed.

Upon finishing the diagnosis, both POWER and STATUS LEDs light green.

1.5.2. LED Behavior while Operating

This Switching Hub has a set of LEDs for each port. These LEDs indicate the operation sta

tus of each port.

● System LED

LED

Behavior

Description

POWER LED

Green Light

Power is ON

Off

Power is OFF

STATUS LED

Green Light

The system is operating nor

mally.

Orange Light

The system is staring up.

Orange Blink

Malfunction
(Contact the shop)

SD CARD LED

Green Light

SD card is inserted

Green Blink

Accessing to SD card

Orange Light

SD card error

Off

Not inserted

STACK ID LED

"H" and STACK ID are displayed
alternately.

Master device

"h" and STACK ID are displayed
alternately.

Backup-master device

STACK ID only

Slave device

● 10/100/1000BASE-T port LED (Ports 1 to 24)

LED

Behavior

Description

LINK/ACT.

Green Light

1000Mbps link established in full-duplex.

Green Blink

Transmitting/receiving packets in 1000Mbps
full-duplex.

Orange Light

10/100Mbps link established.

Orange Blink

Transmitting/receiving packets at 10/
100Mbps.

Off

No device connected.

Содержание ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZEQUO 6400

Отзывы:

Похожие инструкции для ZEQUO 6400

Бренды по названию

Популярные бренды

Panasonic ZEQUO 6400, Руководство по эксплуатации

Результаты поиска

Содержание ZEQUO 6400

Отзывы:

Похожие инструкции для ZEQUO 6400

Бренды по названию

Популярные бренды