Panasonic ZEQUO 6400 Скачать руководство пользователя страница 698

Страница: 698 / 1058

61. Packet Storm Commands

699



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.



Example

To configure the auto recover time to 5 minutes:

61.3. config traffic control log state



Description

This command is used to configure the traffic control log state. When the log state is

enabled, traffic control states are logged when a storm occurs and when a storm is

cleared. If the log state is disabled, traffic control events are not logged.

The log state is only applicable for shutdown mode. Since shutdown mode only support

broadcast and multicast storm control, doesn't support unicast storm control. The log only

generate for broadcast and multicast storm control.



Format

config traffic control log state [enable | disable]



Parameters



Restrictions

Only Administrator, Operator and Power-User level users can issue this command.

<min 0> Enter the automatic recovery time used here. This value will specifies the time to be 0

otherwise known as 'no recovery mode'.

Enter the automatic recovery time used here. This value must be between 1 and 65535
minutes.

Zxxx0:admin# config traffic control auto_recover_time 5
Command: config traffic control auto_recover_time 5

Success.

Zxxx0:admin#

state

Specifies the traffic control log state.
enable

Specifies that traffic control state will be logged when a storm occurs.

disable

Specifies that the traffic control state will be disabled.

Содержание ZEQUO 6400



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZEQUO 6400

Отзывы:

Похожие инструкции для ZEQUO 6400

Бренды по названию

Популярные бренды

Panasonic ZEQUO 6400, Руководство по эксплуатации

Результаты поиска

Содержание ZEQUO 6400

Отзывы:

Похожие инструкции для ZEQUO 6400

Бренды по названию

Популярные бренды