OPTRONIC LVMC Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 97

OPTRONIC LVMC Скачать руководство пользователя страница 94

Interface A2, Release Date: 02.03.2022

Page 94

LVMC User Manul A2 - 499.027.82

OPTRONIC AG
SWITZERLAND

Unteregger Strasse 53
CH-9403 Goldach

Phone: +41 (0)71 844 02 00
Fax:

+41 (0)71 844 02 10

e-mail: [email protected]
web: www.optronic.ch

14.4

Embodiment DIO: 3 Digital Outputs and 2 Digital I/Os

Assignment D-Sub Connector Embodiment DIO

Pin Assignment

1

Shield (The shield must be connected at both cable ends to the respective
device housing.)

6

Ground (0V)

2

Power Supply (+24V)

4

Common switching voltage for optocoupler outputs and optocoupler I/Os
(Pins 3, 5, 7, 8 und 9)

8

Output 3

Optocoupler outputs

Positive polarity:

When active, the transistor is conductive

Negative polarity:

When active, the transistor is not conducting

7

Output 2

3

Output 1
(Monitoring 2)

9

I/O 1 (Bit 2

0

)

Bidirectional optocoupler inputs/outputs (I/Os)

5

I/O 2 (Bit 2

1

)

Warning

If the bidirectional optocoupler inputs/outputs at pin 5 and pin 9 are used as inputs, it must be ensured that
the voltage at these pins is never higher than the voltage at pin 4! If the voltage is higher, the in the LVMC
integrated hardware protection circuit will be activated, which may damage externally connected compo-
nents!

D-Sub Connector

«
...
92
93
94
95
96
...
»

Содержание LVMC


































































































Отзывы:

Нет отзывов