Mitsubishi A1SH Скачать руководство пользователя страница 93

Страница: 93 / 186

8. LOADING AND INSTALLATION

8 - 9

MELSEC-A

8.5

Installation and Removal of Module

This section explains the mounting and removal of the I/O module and special
function module, etc., to and from the base module.

(1)

Module mounting

The module mounting procedure is as follows.

Insert the module mounting
hook into the module mounting
hole in the base unit.

Install the module on the base
unit by pushing the top forward.

Make sure the hook is securely
inserted in the module mounting
hole in the base unit. Then, secure
the module with the module mounting
screw.

End

Base unit

Module

Module
mounting
hook

Module mounting hole

Module mounting screw

Module

Base
unit

Module

connector

POINT

(1)

When securing the module, be sure to
insert the module mounting hook into
the module mounting hole. If the
module is forcibly secured without
insertion, the module's connector or
the module itself may be damaged.

(2)

Always turn the power supply OFF
before mounting or removing any
module.

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 93 / 186

Результаты поиска

Содержание A1SH

Отзывы: