Mitsubishi A1SH Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 186

Mitsubishi A1SH Скачать руководство пользователя страница 37

2. SYSTEM CONFIGURATION

2 - 19

MELSEC-A

REMARK

I/O cables with connectors for I/O modules with 40-pin connector specifications (A1SX41, A1SX42,
A1SY41, A1SY42, etc.) or 37-pin D-sub connector specifications (A1SX81, A1SY81, A1SY81EP) are
available.
Consult your nearest Mitsubishi representative for I/O cables with connectors.

(2)

Peripheral devices

Item

Module

Remarks

Plasma handy

Graphic

programmer

A6PHP-SET

•

Main body of A6PHP

•

SW[ ]GP-GPPAEE : A-series GPP function system disk

•

SW[ ]GP-GPPKEE : K-series GPP function system disk

•

SW0-GPPU : User disk (2DD)

•

AC30R4 : RS-422 cable (3 m (9.84 ft) long)

Intelligent GPP

A6GPP-SET

•

Main body of A6GPP

•

SW[ ]GP-HGPAEE : A-series GPP function system disk

•

SW[ ]GP-HGPKEE : K-series GPP function system disk

•

SW0-GPPU : User disk (2DD)

•

AC30R4 : RS-422 cable (3 m (9.84 ft) long)

Composite

video cable

AC10MD

•

Connects A6GPP and monitor display. (1 m (3.28 ft) long)

AC30R4

3 m (9.84 ft) long

RS-422 cable

AC300R4

30 m (98.4 ft) long

Used for storing user program (3.5 in., formatted)

SW0-GPPU

2DD

User disk

SW0S-USER

2HD

Connects CPU and A6GPP/A6PHP.

Cleaning disk

SW0-FDC

Applicable to

A6GPP/A6PHP

Used for cleaning disk drive.

Printer

K6PR-K

A7NPR-S1

•

For printing out program circuit diagrams and various lists.

RS232C cable

AC30R2

Connection cable for between A6GPP/A6PHP and printer (K6PR-K, A7NPR-

S1, and a general-purpose printer with RS-232C interface)

3m (9.84 ft.) long

Printer paper

K6PR-Y

K7PR-Y

Printer paper for K6PR(S1) and K6PR-K. 9-inch paper. 2000 sheets per unit.

Printer paper for A7PR and A7NPR. 11-inch paper. 2000 sheets per unit.

Inked ribbon for

K6PR(K)

K6PR-R

Replacement inked ribbon for K6PR-K.

Inked ribbon for

A7NPR-S1

A7NPR-R

Replacement inked ribbon for A7NPR-S1.

A7PUS

Read/write of the program is performed by connecting to the CPU main

module with a RS-422 cable (AC30R4-PUS). (5VDC 0.4A)

Programming module

A8PUE

Read/write of the program is performed by connecting to the CPU main

module with a RS-422 cable (AC30R4-PUS, AC20R4-A8PU). (5VDC 0.4A)

AC30R4-PUS

Connection cable for between the CPU main module and A7PUS, A8PUE.

3m (9.84 ft.) long

RS-422 cable

AC20R4-A8PU

Connection cable for between the CPU main module and A8PUE.

2m (6.56 ft.) long

P-ROM write module

A6WU

Used to write the program in the CPU/A6PHP main module to a ROM, or to

read out the program in the ROM for the CPU main module.

Connect to the CPU/A6PHP with an AC30R4/AC03WU cable.

Data access module

A6DU-B

Used for monitoring the CPU devices, changing the setting values/ current

values, and displaying the operation status. (5VDC 0.23A)

Connect to the CPU with an AC30R4-PUS cable.

AC30R4

AC300R4

Connection cable for between the CPU main module and A6WU. 3m/30m

(9.84 ft./98.43 ft.) long.

RS-422 cable

AC03WU

Connection cable for between the A6PHP main module and A6WU. 0.3m

(0.98 ft.) long.

«
...
35
36
37
38
39
...
»

Содержание A1SH



























































































































































































Отзывы:

Нет отзывов