Mitsubishi A1SH Скачать руководство пользователя страница 166

Страница: 166 / 186

APPENDICES

APP - 32

MELSEC-A

Table 2.2

Special registers list (Continue)

Number

Name

Description

Details

Applicable CPU

Mode setting

0 Auto-

matic
online
return
enabled

• When an I/O module or a remote terminal

module caused communication error, the
station is placed offline.

• Communication with normal stations is

continued.

• The station recovering from a

communication error automatically
resumes communication.

1 Auto-

matic
online
return
disabled

• When an I/O module or a remote terminal

module caused communication error, the
station is placed offline.

• Communication with normal stations is

continued.

• Though a faulty station returned to normal,

communication is not restored unless the
station module is restarted.

2 Trans-

mission
stop at
online
error

• When an I/O module or a remote terminal

module caused communication error,
communication with all stations is stopped.

• Though a faulty station returned to normal,

communication is not restored unless the
station module is restarted.

D9173

Mode setting

0: Automatic online

return enabled

1: Automatic online

return disabled

2: Transmission stop

at online error

3: Line check

3 Line

check

• Checks hardware and connecting cables

of I/O modules and remote terminal
modules.

—

Usable with A2C
and A52G.

D9174

Setting of the
number of retries

Number of retries

• Sets the number of retries executed to I/O modules and

remote terminal modules which caused communication
error.

• Set for 5 times at power on.
• Set range: 0 to 32
• If communication with an I/O module or a remote

terminal module is not restored to normal after set
number of retries, such module is regarded as a faulty
station.

—

Usable with A2C
and A52G.

D9175

Line error retry
counter

Number of retries

• Stores the number of retries executed at line error (time

out).

• Data becomes 0 when line is restored to normal and

communication with I/O modules and remote terminal
modules is resumed.

—

Usable with A2C
and A52G.

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 166 / 186

Результаты поиска

Содержание A1SH

Отзывы: