manualshive.com logo in svg

Mitsubishi A1SH, Руководство пользователя, Страница: 17 / 186

Поделиться
Скачать
Mitsubishi A1SH Скачать руководство пользователя страница 17

1. OVERVIEW

1 - 2

MELSEC-A

1.2

Features

(1)

High-speed operation processing speed

Compared to the conventional A1SCPU, the A1SHCPU is three times and
A2SHCPU (-S1) is four times faster in the operation processing speed,
respectively.

Item

A1SHCPU

A2SHCPU(-S1)

A1SCPU

Operation processing speed *1

0.33 

µ

s

0.25 

µ

s

1 

µ

s

*1

I/O processing :  Refresh and LD instruction

(2)

Addition of new dedicated instructions

The CC-Link dedicated instructions (8 instructions) have been added, making
the operation even easier.

(3)

Increased number of I/O device points

The actual number of I/O points is the same as the AnS series, but each CPU
has 2048 points (X/Y0 to 7FF) of I/O devices.
The added I/O device can be used as the MELSECNET (/B),
MELSECNET/MINI-S3, or CC-Link.

(4)

Increased file register R capacity

The capacity is now max. 8192 points (R0 to 8191), which doubled the AnS
series' 4096 points (R0 to 4095).

(5)

Increased memory capacity (Increased number of comment points)

The A1SHCPU has 64 k bytes, which doubled the A1SCPU's 32 k bytes.
This increased the number of comment points stored in the CPU module 3648
in comparison to the 1600 points in A1SCPU.

(6)

Full compatibility with A1S(S1)/A2SCPU(S1)

Because there is full compatibility of the functions and instructions with
A1S(S1)/A2SCPU(S1), all software packages can be used.
In addition, power supply module, base unit, and I/O modules can be used.

(7)

Compact size

The outside dimensions of the AnSHCPU system with one power supply
module, one CPU, and eight 16-point I/O modules for use with AnS mounted
to the main base unit are:
430 mm (16.9 in.) (W); 130 mm (5.12 in.) (H); and 110 mm (4.33 in.) (D).

Содержание A1SH



























































































































































































Отзывы:

Нет отзывов