Mitsubishi A1SH Скачать руководство пользователя страница 59

Страница: 59 / 186

4. AnSHCPU MODULE

4 - 19

MELSEC-A

No.

Name

Function

(4)

RS-422 connector

•

Used to connect a peripheral device to write/read, monitor, or test a program using a peripheral

device.

•

Close with the cover when not connected to a peripheral device.

(5)

Cover

•

Protects AnSHCPU printed circuit board, memory cassette, RS-422 connector, battery, etc.

•

Execute the following operations with the cover open.

•

Memory cassette connection/disconnection

•

Setting a dip switch

•

Connection to battery connector

•

For mounting the module to the base unit battery replacement

(6)

Module fixing screws

•

For mounting the module to the base unit

(7)

Battery

•

For retaining data such as programs, device latch ranges, file registers, etc.

(See Section 7.2 for battery replacement.)

(8)

DIP switch

•

Used for switching the I/O control method and for setting the memory protect function.

(See Sections 4.4.2 and 4.4.3)

(9)

Battery connector

•

For connection to the battery

(10)

Memory cassette
installing connector

•

For installing the memory cassette

(11)

"POWER" LED

•

5 V DC power display LED

(12)

Base installation hole

•

Hole to install the base unit to a panel such as a control board. (M5 screw)

(13)

Power supply input
terminals

•

Connect the 100 V AC or 200 V AC power for the power input terminal.

(14)

LG terminals

•

Power filter grounding terminal. Has half the voltage level of the input voltage.

(15)

FG terminals

•

Grounding terminal connected to the shielding pattern on the print board.

(16)

DIN rail

•

DIN rail installation hook (2)

(17)

RS-422 connector
cover

•

RS-422 connector cover

(18)

Module connector

•

Connector to install the I/O module or special module.

For the connector not for module installation, install supplied connector cover, or blank cover
(A1SG60) to prevent dust entry.
Number of I/O slots

A1SJHCPU : 5
A1SJHCPU-S8 : 8

(19)

Extension cable
connector

•

Connect the extension cable with the signal send/receive connector with the extension base unit.

(20)

Base cover

•

Extension connector protective cover.

To extend, the area surrounded by the groove below the OUT sign on the base cover must be
removed using tools such as a nipper.

(21)

Module fixing screws

•

Screws to fix the module to the base. (M4

12 screws)

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 59 / 186

Результаты поиска

Содержание A1SH

Отзывы: