Mitsubishi A1SH Скачать руководство пользователя страница 58

Страница: 58 / 186

4. AnSHCPU MODULE

4 - 18

MELSEC-A

A1SJHCPU(S8)

(12)

(13)

(14)
(15)

(16)

(9)

(10)

(4)

(8)

(5)

(7)

(17)

(18)

(20)

(19)

(21)

(3) (2)

(11)

(1)

OUTPUT
5VDC 3A

INPUT
100Ð120VAC
200Ð240VAC

105VA

50/60Hz

INPUT
100-120/200-240VAC

(LG)

(FG)

PULL

OUT

I/D0

I/D1

I/D2

I/D3

I/D4

POWER

RUN

ERROR

STOP

L.CLR

RUN

RESET

MITSUBISHI

MELSEC A1SJHCPU

WARNING

Hazardous
voltage.

No.

Name

Function

(1)

RUN/STOP key
switch

•

RUN/STOP

To start/stop running a sequence program.

•

RESET

To reset the hardware.

To reset an error occurring during operation to initialize operation.

•

LATCH CLEAR :

To clear (turn OFF, or clear to "0") the data in the latch range and

(L.CLR)

non-latch range which are set by parameter.
For the latch clear operation procedure, see Section 4.4.4

(2)

"RUN" LED

•

Indicates that a sequence program operation is being executed with the RUN key

switch set to the RUN position.

The LED remains lit if an error (Section 11.3), which permits sequence
operation to continue, occurs.

•

OFF

The RUN LED goes out in the following cases :

•

When the RUN key switch is in the STOP position.

•

When the remote STOP signal is input.

•

When the remote PAUSE signal is input.

•

Flashing :

The RUN LED flashes in the following cases :

•

When an error which causes sequence operation to stop is detected by the self-

diagnosis function.

•

When the latch clear operation is executed.

(3)

"ERROR" LED

•

Indicates that the self-diagnosis function has detected an error.

When the detected error is set to "not lit" in the ERROR LED indication
priority setting.

•

OFF

Indicates that no error has occurred or that a malfunction has been detected by the

[CHK] instruction.

•

Flashing :

An annunciator (F) is turned ON by the sequence program.

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 58 / 186

Результаты поиска

Содержание A1SH

Отзывы: