Mitsubishi A1SH Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 186

Mitsubishi A1SH Скачать руководство пользователя страница 116

10. MAINTENANCE AND INSPECTION

10 - 5

MELSEC-A

10.3.2

Battery replacement procedure

When the service life of the battery has expired, replace the battery using the
following procedure :

Even if the battery is removed, the memory is backed up by a capacitor for some
time.

However, if the replacement time exceeds the guaranteed value shown in the
following table, the contents of the memory may be lost. Therefore, replace the
battery as quickly as possible.

Replacement of battery

Turn OFF the PLC power supply.

Open the cover on the front of
the AnSCPU.

Remove the old battery from the
holder and remove the lead from
the lead clamp. Then, remove the
lead connector from the connector.

Insert a new battery into the holder
in the correct orientation and con-
nect the lead wires to the connector.
(Clamp the lead with the lead clamp.)
(The red lead is positive, and the
blue one negative.)

Close the cover on the front of the
AnSCPU.

Turn ON the PLC power supply.

Monitor M9006 and check

ON/OFF.

Battery failure

End

OFF

ON

A1SHCPU

A6BAT

Battery
connector

Table 10.4 Backup time by capacitor

Capacitor backup time (Minutes)

Guaranteed value

(MIN)

Actually applied value

(TYP)

5

15

«
...
114
115
116
117
118
...
»

Содержание A1SH



























































































































































































Отзывы:

Нет отзывов