Mitsubishi A1SH Скачать руководство пользователя страница 151

Страница: 151 / 186

APPENDICES

APP - 17

MELSEC-A

POINTS

(1) Contents of the M special relays are all cleared by power off, latch clear or reset

with the reset key switch. When the RUN key switch is set in the STOP

position, the contents are retained.

(2) The above relays with numbers marked 1 remain "on" if normal status is

restored. Therefore, to turn them "off", use the following method:

(a) Method by use program

Insert the circuit shown at right into the

user program and turn on the reset

execution command contact to clear

the special relay M.

Reset execution
command

RST

M9000

Special function relay to be reset

(b) Use the test function of the peripheral device to reset forcibly.

For the operation procedure, refer to the manuals for peripheral devices.

the special relays are turned off.

(3) Special relays marked 2 above are switched on/off in the sequence program.

(4) Special relays marked 3 above are switched on/off in test mode of the

peripheral equipment.

(5) Turn OFF the following special relays after resetting the related special

resisters. Unless the related special registers are reset, the special relays will

be turned ON again even if they are turned reset.

Special Relay

Related Special Resister

M9000

D9100 to D9107

M9001

D9116 to D9123

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 151 / 186

Результаты поиска

Содержание A1SH

Отзывы: