Mitsubishi A1SH Скачать руководство пользователя страница 105

Страница: 105 / 186

9. EMC DIRECTIVE AND LOW-VOLTAGE INSTRUCTION

9 - 5

MELSEC-A

(3) Ethernet module, Web server module

Precautions for using AUI cables, twisted pair cables and coaxial cables are

described below.

(a) Always earth the AUI cables connected to the 10BASE5 connectors.

Because the AUI cable is of the shielded type, strip part of the outer cover

and earth the exposed shield section to the ground on the widest contact

surface as shown below.

AUI cable

Shield

Refer to (1) for the earthing of the shield.

(b) Use shielded twisted pair cables as the twisted pair cables connected to the

10BASE-T/100BASE-TX connectors. For the shielded twisted pair cables,

strip part of the outer cover and earth the exposed shield section to the

ground on the widest contact surface as shown below.

Shielded twisted pair cables

Shield

Refer to (1) for the earthing of the shield.

to the 10BASE2 connectors. Earth the double-shielded coaxial cable by

connecting its outer shield to the ground.

Earth here

Shield

Refer to (1) for the earthing of the shield.

Ethernet is the registered trademark of XEROX Corporation in the US.

(4) I/O and other communication cables

Always earth the shield section of the I/O signal cables and other communication

cables (RS-232-C, RS-422, etc.) in the same manner as described in (1) if the

cables go outside of the control cabinet.

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 105 / 186

Результаты поиска

Содержание A1SH

Отзывы: