Mitsubishi A1SH Скачать руководство пользователя страница 75

Страница: 75 / 186

6. BASE UNIT AND EXTENSION CABLE

6 - 8

MELSEC-A

(2)

Main base modules (A1S52B(S1), A1S55B(S1), A1S58B(S1), A1S65B(S1),
A1S68B(S1))

(1)

POWER

I/O

A1S68B

OUT

(6)

(3)

(2)

(4)

(2)

(5)

(9)

(1)

I/O

A1S58B

OUT

(6)

(3)

(4)

(2)

(5)

(7)

No.

Name

Purpose

(1)

Extension cable connector

Used to connect an extension cable to a main base module.
Remove the connector cover attached to the module and connect the extension cable.

(2)

Base cover

Extension cable connector protective cover.

(3)

Module connector

Used to load a power supply module, I/O or special function module. Put a supplied cover or
blank cover (A1SG60) on any unused connector to protect it from dust.

(4)

Module fixing screw

Used to secure a module to the base module.
Screw size : M4

(5)

Base mounting hole

Used to mount the base module to a control panel. (for M5 screw)

(6)

DIN rail hook

Used to install on a DIN rail.
A1S52B(S1), A1S55B(S1) : One hook
A1S65B(S1), A1S68B(S1), A1S58B(S1) : Two hooks

(7)

FG terminal

Grounding terminal connected to the shield pattern on the PLC board.

A1S52B (S1), A1S55B (S1), A1S58B (S1)

A1S65B (S1), A1S68B (S1)

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 75 / 186

Результаты поиска

Содержание A1SH

Отзывы: