manualshive.com logo in svg

Mitsubishi A1SH, Руководство пользователя, Страница: 126 / 186

Поделиться
Скачать
Mitsubishi A1SH Скачать руководство пользователя страница 126

11. TROUBLESHOOTING

11 - 10

MELSEC-A

11.3

Error Code List

If an error occurs in the RUN mode, an error display or error code (including a step
number) is stored in the special register by the self-diagnosis function.  The error
code reading procedure and the causes of and corrective actions for errors are
shown in Table 11.1.

11.3.1

Error codes

The followings are the explanation about the descriptions and the causes of the
error messages, error codes and the detailed error codes, and their corrective
actions.

The detailed error codes are stored in D9092 only when using the dedicated
instruction for CC-Link.

Table 11.1  Error codes

Error Message

Error
Code

(D9008)

Detailed

Error
Code

(D9092)

CPU

States

Error and Cause

Corrective Action

Instruction code, which cannot be
decoded by CPU module, is included
in the program.

(1)

Memory cassette including 
instruction code, which cannot 
be decoded, has been loaded.

(2)

Since the memory contents have
changed for some reason, 
instruction code, which cannot 
be decoded, has been included.

(1)

Read the error step by use of 
peripheral equipment and correct 
the program at that step.

(2)

In the case of memory cassette, 
rewrite the contents or replace 
the cassette with a memory 
cassette which stores correct 
contents.

101

Instruction code, which cannot be
decoded by CPU module, is included
in the program.

(1)

Memory cassette including 
instruction code, which cannot 
be decoded, has been loaded.

(2)

Since the memory contents have
changed for some reason, 
instruction code, which cannot 
be decoded, has been included.

(1)

Read the error step by use of 
peripheral equipment and correct 
the program at that step.

(2)

In the case of memory cassette, 
rewrite the contents or replace 
the cassette with a memory 
cassette which stores correct 
contents.

103

Device specified by a dedicated
instruction for CC-Link is not correct.

104

A dedicated instruction for CC-Link
has incorrect program structure.

"INSTRCT.

CODE ERR"

10

105

Stop

A dedicated instruction for CC-Link
has incorrect command name.

Read the error step using a peripheral
device and correct the program of the
step.

"PARAMETER

ERROR"

11

Stop

The contents of parameters of CPU
memory have changed due to noise
or the improper loading of memory.

(1)

Load the memory cassette 
correctly.

(2)

Read the parameter contents of 
CPU memory, check and correct 
the contents, and write them to 
CPU again.

"MISSING END

INS."

12

Stop

There is no  END  ( FEND )
instruction in the program.

Write  END  instruction at the end of
program.

Содержание A1SH



























































































































































































Отзывы:

Нет отзывов