manualshive.com logo in svg

Mitsubishi A1SH, Руководство пользователя, Страница: 148 / 186

Поделиться
Скачать
Mitsubishi A1SH Скачать руководство пользователя страница 148

APPENDICES

APP - 14

MELSEC-A

Table 2.1

Special relay list (Continue)

Number

Name

Description

Details

Applicable CPU

M9095

Duplex operation
verify error

OFF: Normal
ON: Duplex operation

verify error

• During duplex operation of the operating CPU with a

stand-by CPU, verification is performed by the both
to each other. Turned on when a verify error
occurred.

—

Dedicated to A3V.

M9096

A3VCPU A
selfcheck error

OFF: No error
ON: Error

• Turn on when a self-check error occurred on the

A3VCPU A mounted next to the A3VTU.

—

Dedicated to A3V.

M9097

A3VCPU B
selfcheck error

OFF: No error
ON: Error

• Turn on when a self-check error occurred on the

A3VCPU B mounted next to the A3VCPU A.

—

Dedicated to A3V.

M9098

A3VCPU C
selfcheck error

OFF: No error
ON: Error

• Turn on when a self-check error occurred on the

A3VCPU C mounted next to the A3VCPU B.

—

Dedicated to A3V.

M9099

A3VTU selfcheck
error

OFF: No error
ON: Error

• Turned on when a self-check error occurred on the

A3VTU.

—

Dedicated to A3V.

M9100

SFC program
registration

OFF: No SFC program
ON: SFC program

registered

• Turned on if the SFC program is registered, and

turned off if it is not.

—

Usable with AnN

,

AnA

, AnU,

A2AS, QCPU-A
(A Mode),  A2C,
A0J2H, AnS,
AnSH, A1FX and
A52G.

2

M9101

SFC program
start/stop

OFF: SFC program stop
ON: SFC program start

• Should be turned on by the program if the SFC

program is to be started. If turned off, operation
output of the execution step is turned off and the
SFC program is stopped.

—

Usable with AnN

,

AnA

, AnU,

A2AS, QCPU-A
(A Mode), A2C,
A0J2H, AnS,
AnSH, A1FX and
A52G.

2

M9102

SFC program
starting status

OFF: Initial start
ON: Continuous start

• Selects the starting step when the SFC program is

restarted using M9101.
ON: Started with the step of the block being

executed when the program stopped.

OFF: All execution conditions when the SFC program

stopped are cleared, and the program is started
with the initial step of block 0.

• Once turned on, the program is latched in the system

and remains on even if the power is turned off.
Should be turned off by the sequence program when
turning on the power, or when starting with the initial
step of block 0.

—

Usable with AnN

,

AnA

, AnU,

A2AS, QCPU-A

(A Mode), A2C,

A0J2H, AnS,

AnSH, A1FX and

A52G.

2

M9103

Consecutive step
transfer
enable/disable

OFF: Consecutive step

transfer disable

ON: Consecutive step

transfer enable

• Selects consecutive or step-by-step transfer of steps

of which transfer conditions are established when all
of the transfer conditions of consecutive steps are
established.
ON:

Consecutive transfer is executed.

OFF: One step per one scan is transferred.

—

Usable with AnN

,

AnA

, AnU,

A2AS, QCPU-A

(A Mode), A2C,

A0J2H, AnS,

AnSH, A1FX and

A52G.

M9104

Consecutive
transfer
prevention flag

OFF: Transfer complete
ON: Transfer incomplete

• Turned on when consecutive transfer is not executed

with consecutive transfer enabled. Turned off when
transfer of one step is completed.
Consecutive transfer of a step can be prevented by
writing an AND condition to corresponding M9104.

—

Usable with AnN

,

AnA

, AnU,

A2AS, QCPU-A

(A Mode), A2C,

A0J2H, AnS,

AnSH, A1FX and

A52G.

: Usable with AnN and AnA which are compatible with SFC.

For the AnN and AnA which are compatible with SFC, refer to the MELSAP-II Programming Manual.

Содержание A1SH



























































































































































































Отзывы:

Нет отзывов