manualshive.com logo in svg

Mitsubishi A1SH, Руководство пользователя, Страница: 127 / 186

Поделиться
Скачать
Mitsubishi A1SH Скачать руководство пользователя страница 127

11. TROUBLESHOOTING

11 - 11

MELSEC-A

Table 11.1  Error codes (Continue)

Error Message

Error
Code

(D9008)

Detailed

Error
Code

(D9092)

CPU

States

Error and Cause

Corrective Action

"CAN’T

EXECUTE(P)"

13

Stop

(1)

There is no jump destination or 
multiple destinations specified by
the  CJ ,  SCJ ,  CALL ,

 CALLP , or  JMP  instruction.

(2)

Although there is no  CALL 
instruction, the  RET  instruction 
exists in the program and has 
been executed.

(3)

The  CJ ,  SCJ ,  CALL ,

 CALLP , or  JMP  instruction

has been executed with its jump 
destination located below the

 END  instruction.

(4)

The number of the  FOR 
instructions is different from that 
of the  NEXT  instructions.

(5)

A  JMP  instruction is given 
within a  FOR to NEXT  loop 
causing the processing to exit 
the loop.

(6)

Processing exited subroutine by 
the  JMP  instruction before 
execution of the  RET 
instruction.

(7)

Processing jumped into a step in

a  FOR to NEXT  loop or into

a 

subroutine by the  JMP 
instruction.

Read the error step by use of
peripheral equipment and correct the
program at that step.
(Insert a jump destination or reduce
multiple destinations to one.)

"CHK FORMAT

ERR"

14

Stop

(1)

Instructions (including  NOP ) 
except LD X , LDI X , AND X
and ANI X  are included in the 

 CHK  instruction circuit block.

(2)

Multiple  CHK  instructions are 
given.

(3)

The number of contact points in 
the  CHK  instruction circuit

block exceeds 

150.

(4)

There is no 

CJ P

circuit block before the  CHK 
instruction circuit block.

(5)

The device number of D1 of the 

CHK D1 D2  instruction is 

different from that of the contact 
point before the  CJ P
instruction.

(6)

Pointer P254 is not given to the 
head of the  CHK  instruction 
circuit block.

CHK

P254

D1 D2

(1)

Check the program in the CHK
instruction circuit block according 
to item (1) to (7) in the left 
column.
Correct problem using the 
peripheral equipment and

perform operation 

again.

(2)

This error code is only effective 
when the input/output control 
method is a direct method.

Содержание A1SH



























































































































































































Отзывы:

Нет отзывов