Mitsubishi A1SH Скачать руководство пользователя страница 162

Страница: 162 / 186

APPENDICES

APP - 28

MELSEC-A

Table 2.2

Special registers list (Continue)

Number

Name

Description

Details

Applicable CPU

D9100

D9101

D9102

D9103

D9104

D9105

D9106

D9107

Fuse blown
module

Bit pattern in units of 16
points of fuse blow
modules

• Output module numbers (in units of 16 points), of which

fuses have blown, are entered in bit pattern. (Preset
output unit numbers when parameter setting has been
performed.)

D9100

D9101

D9107

15 14

12 11

10 9 8

6 5 4 3 2 1 0

0 0

0 0 1

(Y80)

0 0 0 0 0 0 0

0 0

(Y1A)

0 0

0 0 0 0 0 0 0

0 0

0 0 0

Indicates fuse blow.

D9100

D9101

D9107

15 14

12 11

10 9 8

6 5 4 3 2 1 0

0 0

(YC0)

0 0

0 0 0 0 0 0 0

(Y1F0)

0 0

0 0 0 0 0 0 0

0 0

0 0 0

Y7
BC

Y7
30

• Fuse blow check is executed also to the output module of

remote I/O station.
(If normal status is restored, clear is not performed.
Therefore, it is required to perform clear by user
program.)

Usable with all

types of CPUs

Only remote

I/O station

information is

valid for A2C.

D9100

Fuse blow
module

Fuse blow module bit
pattern

• Stores the output module number of the fuses have

blown in the bit pattern.

b15

D9100

b8 b7 b6 b5 b4 b3 b2 b1

0 is fixed.

Indicates the module
for setting switch 0.

Indicates the module
for setting switch 1.

Indicates the module
for setting switch 2.

Indicates the module
for setting switch 3.

Indicates the module for setting
switch 4 or the module for
extension base unit slot 0.

Indicates the module for setting
switch 5 or the module for
extension base unit slot 1.

Indicates the module for setting
switch 6 or the module for
extension base unit slot 2.

Indicates the module for setting switch 7 or
the module for extension base unit slot 3.

—

Dedicated to

A0J2H.

D9108

D9109

D9110

D9111

D9112

D9113

D9114

Step transfer
monitoring timer
setting

Timer setting value and
the F number at time
out

• Sets value for the step transfer monitoring timer and the

number of F which turns on when the monitoring timer
timed out.

b15 to b8 b7 to b0

Timer setting
(1 to 255 sec
in seconds)
F number setting

(By turning on any of M9108 to M9114, the monitoring
timer starts. If the transfer condition following a step
which corresponds to the timer is not established within
set time, set annunciator (F) is tuned on.

—

Usable with AnN

, AnA, AnU,

A2AS, AnA

board, QCPU-A

(A Mode), A2C,

A0J2H, AnS,

AnSH, A1FX and

A52G.

: Usable with AnN and AnA which are compatible with SFC.

For the AnN and AnA which are compatible with SFC, refer to the MELSAP-ll Programming Manual.

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 162 / 186

Результаты поиска

Содержание A1SH

Отзывы: