Mitsubishi A1SH Скачать руководство пользователя страница 158

Страница: 158 / 186

APPENDICES

APP - 24

MELSEC-A

Table 2.2

Special registers list (Continue)

Number

Name

Description

Details

Applicable CPU

D9052

Error step

Step number in which
an error occurred.

• Stores the step number in which error 84 occurred in the

SFC program in BIN code.
Stores "0" when errors 80, 81 and 82 occurred.
Stored the block starting step number when error 83
occurred.

—

D9053

Error transfer

Transfer condition
number in which an
error occurred.

• Stores the transfer condition number in which error 84

occurred in the SFC program in BIN code.
Stored "0" when errors 80, 81, 82 and 83 occurred.

—

D9054

Error sequence
step

Sequence step number
in which an error
occurred.

• Stores the sequence step number of transfer condition

and operation output in which error 84 occurred in the
SFC program in BIN code.

—

Usable with

AnN

, AnA

AnU, A2S,

QCPU-A

(A Mode), A2C,

A0J2H, AnS,

AnSH, A1FX and

A52G.

D9055

Status latch
execution step
number

Status latch execution
step number

• Stores the step number when status latch is executed.
• Stores the step number in a binary value if status latch is

executed in a main sequence program.

• Stores the block number and the step number if status

latch is executed in a SFC program.

Block No.

(BIN)

Step No.

(BIN)

Higher 8 bits

Lower 8 bits

—

Usable with AnA,

A2AS, AnA

bpard, AnU and

QCPU-A

(A Mode).

Stores the software version of the CPU module's internal
system in ASCII codes.
Example: Stores "41

" for version A.

Note) The software version of the internal system may be

different from the version marked on the housing.

5: This function is available with the CPU of the

following S/W versions or later.

CPU Type Name

Software Version

A2ACPU (P21/R21), A2ACPU-

S1 (P21/R21)

S/W version W

(Manufactured in July, 1998)

A3ACPU (P21/R21)

S/W version X

(Manufactured in July, 1998)

A2UCPU (S1), A3UCPU,

A4UCPU

S/W version H

(Manufactured in July, 1998)

A1SJHCPU, A1SHCPU,

A2SHCPU

S/W version H

(Manufactured in May, 1998)

A2USCPU (S1)

S/W version Y

(Manufactured in July, 1998)

A2USHCPU-S1

S/W version E

(Manufactured in July, 1998)

D9060

Software version

Software version of
internal system

Can be used only

with AnU, A2US,

or AnSH.

: Usable with AnN and AnA which are compatible with SFC.

For the AnN and AnA which are compatible with SFC, refer to the MELSAP-ll Programming Manual.

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 158 / 186

Результаты поиска

Содержание A1SH

Отзывы: