Mitsubishi A1SH Скачать руководство пользователя страница 172 | Manualshive

Страница: 172 / 186

Mitsubishi A1SH Скачать руководство пользователя страница 172

APPENDICES

APP - 38

MELSEC-A

Appendix 3.3.3

The precaution when utilizing the sequence program

Please follow the procedures below for applying the parameter and program
created for AnSCPU to AnSHCPU:

1.

Select the 'Read File' from the initial setting menu after starting up the GPP
function software.

2.

Read the parameter and program files created for AnSCPU from the floppy or
hard disk, and then write those parameter and program into a peripheral
device. (Such file reading is required for performing the procedure described
in 3.)

3.

Using the item PLC type change in the initial setting menu, change the CPU
type name to A3 which is the one specified for AnSHCPU. (Perform the
procedure as given in 4, since the parameter is reset to the default setting.)

4.

In the file maintenance menu, read the parameter and program created for
AnSCPU from the floppy or hard disk into peripheral devices. (Ignore the error
message 'Unmatched PLC Type' even if such a message may be given.)

The above procedures allow the parameter and program for AnSCPU to be used
for AnSHCPU, without any change or modification.

Appendix 3.3.4

System confirmation by high-speed instruction processing

Confirm effects on the user system by the instruction processing speed and the
reduction of the scan time.

Appendix 3.3.5

Handling conventional memory cassettes

Conventional memory cassettes A1SMCA-2KE/8KE/8KP (for A1SCPU) and
A2SMCA-14KE (for A2SCPU) cannot be used for A1SHCPU and A2SHCPU(S1).
(Used only for A1SJHCPU(S8))

The new type memory cassettes A1SNMCA-2KE/8KE/8KP (for
A1SJHCPU(S8)/A1SHCPU) and A2SNMCA-30KE (for A2SHCPU(S1)) should be
used.

«
...
170
171
172
173
174
...
»

Содержание A1SH



























































































































































































Отзывы:

Нет отзывов