Mitsubishi A1SH Скачать руководство пользователя страница 124

Страница: 124 / 186

11. TROUBLESHOOTING

11 - 8

MELSEC-A

11.2.7

Flowchart used when the output load of the output module does not come ON

YES

0 V

Specified
voltage

0 V

(monitor signal
OFF)

Specified
voltage

Output load does not

come ON.

Is the indicator

LED of the output mod-

ule ON?

Is the voltage

of the power supply for

the load applied?

Is voltage

across the output

module's output COM

terminals as

specified?

Failure of output module.
Replace output module.

Check rush current when
the output load reaches
the maximum number of
simultaneous ON signals.

Check the output state in
monitor mode with the pro-
grammer.

Check the Input signal in
monitor mode with the pro-
grammer.

Check the wiring load of
the power supply for the
load and restore the
power.

Check the load wiring and
load and restore the
power.

Change the output relay
number to adjust the rush
current to comply with
specifications.

Is the indicator

LED of the input mod-

ule ON?

Measure the voltage be-
tween the module input
and COM terminal.

Check external wiring
and external input
equipment.

Consult your nearest
Mitsubishi representative.

POINT

If the input or load signals are not switched OFF, see Section 11.4 I/O
Connection Troubleshooting and take corrective measures.

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 124 / 186

Результаты поиска

Содержание A1SH

Отзывы: