Mitsubishi A1SH Скачать руководство пользователя страница 146

Страница: 146 / 186

APPENDICES

APP - 12

MELSEC-A

Table 2.1

Special relay list (Continue)

Number

Name

Description

Details

Applicable CPU

M9077

Sequence
accumulation
time
measurement

OFF: Time not elapsed
ON: Time elapsed

• Compares the setting value at D9077 with the time

elapsed from the start of measurement
(accumulation time) at every scan. Then, performs
the following operations:
Setting value > Accumulation time:

Turns M9077 ON and clears the accumulation
time.

Setting value < Accumulation time:

Turns M9077 from ON to OFF and clears the
accumulation time. When M9077 is already OFF,
clears the accumulation time.

When 1 to 255 is designated at D9077, M9077 is

turned ON at the first scan.

When the value other than 1 to 255 is designated

at D9077, the value in D9077 is reset to 0 and
M9077 is always turned OFF.

—

Dedicated to

QCPU-A (A Mode)

M9078

Test mode
request error flag

OFF: No error
ON: Error

• Turned on when test mode is not available though a

test mode request was made from a peripheral
device. Turned off if test mode becomes available by
making another test mode request.

—

Dedicated to A73.

M9079

Servo program
setting error flag

OFF: No data error
ON: Data error

• Turned on when the positioning data of the servo

program designated by the DSFRP instruction has
an error.
Turned off when the data has no error after the

DSFRP instruction is executed again.

—

Dedicated to A73.

Turned ON/OFF according to the number of remaining
instructions ( RIRD / RIWT / RISEND / RIRCV )
being executable simultaneously at one scan.

OFF: Number of remaining instructions executable

simultaneously: 1 to 10

ON: Number of remaining instructions executable

simultaneously: 0

By assigning M9080 as execution condition, the
number of instructions above executed simultaneously
at one scan can be limited to 10 or less.

4: This function is available with the CPU of the

following S/W versions or later.

CPU Type Name

Software Version

Q02CPU-A, Q02HCPU-A,

Q06HCPU-A

A1SJHCPU, A1SHCPU,

A2SHCPU

Available with all versions

A2UCPU(S1), A3UCPU,

A4UCPU

S/W version Q (Manufactured

in July, 1999)

A2USCPU(S1)

S/W version E

(Manufactured in July, 1999)

A2USHCPU-S1

S/W version L

(Manufactured in July, 1999)

M9080

BUSY flag for
execution of CC-
Link dedicated
instruction

OFF: Number of

remaining
instructions
executable
simultaneously:
1 to 10

ON: Number of

remaining
instructions
executable
simultaneously: 0

Can be used only

with AnU, A2US, or

AnSH, QCPU-A

(A Mode)

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 146 / 186

Результаты поиска

Содержание A1SH

Отзывы: