Mitsubishi A1SH Скачать руководство пользователя страница 153

Страница: 153 / 186

APPENDICES

APP - 19

MELSEC-A

Table 2.2

Special registers list (Continue)

Number

Name

Description

Details

Applicable CPU

D9003

SUM instruction
detection bits

The number of bits
detected by SUM
instruction detection.

• The number of bits detected by execution of the SUM

instruction are stored. in BIN code and updated every
execution thereafter.

—

Dedicated to

A0J2H.

D9004

MINI link master
module error

Error detection status

• Error status of the MINI (S3) link detected on loaded

MINI (S3) link module is stored.

b15

b8 b7

Bits which correspond
to the signals of MINI
(S3) link module,
shown below, are
turned on as the signals
are turned on.

Hardware error
(X0/X20)
MINI(S3) link error
detection (X6/X26)
MINI(S3) link
communication error
(X7/X27)

5 4 3 2 1

8 7

5 4 3 2 1

Data communication
between the PLC CPU
and MINI (S3) link
module is disabled.

—

Usable with AnA,

A2AS, AnA

board and AnU.

D9005

AC DOWN
counter

AC DOWN count

• 1 is added each time input voltage becomes 85% or less

of rating while the CPU unit is performing operation, and
the value is stored in BIN code.

Usable with all

types of CPUs.

D9006

Battery low

Indicates the CPU
module of which battery
voltage is low.

• Bits which correspond to CPU of which battery is low are

turned on in D9006, as shown below.

CPU B
CPU C

CPU A

0: Normal
1: Battery low

B15

—

Dedicated to

A3V.

D9008

Shelf-diagnostic
error

Self-diagnostic error
number

• When error is found as a result of self-diagnosis, error

number is stored in BIN code.

Usable with all

types of CPUs.

• When one of F0 to 255 is turned on by OUT F or

SET F , the F number, which has been detected
earliest among the F numbers which have turned on, is
stored in BIN code.

• D9009 can be cleared by RST F or LEDR instruction.

If another F number has been detected, the clearing of
D9009 causes the next number to be stored in D9009.

Unusable with

A3, A3N, A3A,

A73 and A3N

board.

D9009

Annunciator
detection

F number at which
external failure has
occurred

• When one of F0 to 255 is turned on by OUT F or

SET F , the F number, which has been detected earliest
among the F numbers which have turned on, is stored in
BIN code.

• D9009 can be cleared by executing RST F or LEDR

instruction or moving INDICATOR RESET switch on
CPU front to ON position. If another F number has been
detected, the clearing of D9009 causes the nest number
to be stored in D9009.

—

Usable with A3,

A3N, A3A, A73

and A3N board.

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 153 / 186

Результаты поиска

Содержание A1SH

Отзывы: