manualshive.com logo in svg

Mitsubishi A1SH, Руководство пользователя, Страница: 50 / 186

Поделиться
Скачать
Mitsubishi A1SH Скачать руководство пользователя страница 50

4. AnSHCPU MODULE

4 - 10

MELSEC-A

Table 4.3 Devices (Continued)

Device

Application range (Number of points)

Explanation

P

Pointer

P0 to P255 (256 points)

Indicates the destination of branch instructions (CJ, SCJ, CALL,
JMP).

I

Pointer for
interruption

I0 to I31 (32 points)

Indicates an interrupt program corresponding to the interrupt
source.

K

Decimal constant

K-32768 to 32767
(16-bit instruction)

K-2147483648 to 2147483647
(32-bit instruction)

Used to specify the timer/counter set value, pointer number,
interrupt pointer number, the number of bit device digits, and
basic and application instruction values.

H

Hexadecimal
constant

H0 to FFFF (16-bit instruction)

H0 to FFFFFFFF (32-bit instruction)

Used to specify the basic and application instruction values.

REMARK

The step relay (S) may be used in the same manner as the internal relay (M). The step relay is useful
when writing a program which has two functions or applications, i.e., the step relay can be used
specifically in accordance with the function or application, independently of the internal relay.

Содержание A1SH



























































































































































































Отзывы:

Нет отзывов