Mitsubishi A1SH Скачать руководство пользователя страница 67

Страница: 67 / 186

5. POWER SUPPLY MODULE

5 - 5

MELSEC-A

No.

Name

Description

[4]

LG terminal

Grounding for the power supply filter. The potential of A1S61P or A1S62P terminal is 1/2 of the input
voltage.

[5]

Power supply input
terminals

Used to connect a 24 V DC power supply.

[6]

Power supply input
terminals

Used to connect 100 V AC to 200 V AC power supply.

[7]

Terminal screw

M3.5

[8]

Terminal cover

The protective cover of the terminal block.

[9]

Module fixing screw

Used to fix the module to the base unit.
(M4 screw, tightening torque : 59 to 88 N·cm

POINT

(1)

Do not cable to the unused terminals such as FG and LG on the terminal
block (terminals whose name is not printed on the terminal cover).

(2)

Be sure to ground the terminal LG to the protective ground conductor
with class D (class-3) grounding or above.

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 67 / 186

Результаты поиска

Содержание A1SH

Отзывы: