Mitsubishi A1SH Скачать руководство пользователя страница 164

Страница: 164 / 186

APPENDICES

APP - 30

MELSEC-A

Table 2.2

Special registers list (Continue)

Number

Name

Description

Details

Applicable CPU

D9125

D9126

D9127

D9128

D9129

D9130

D9131

D9132

Annunciator
detection number

Annunciator detection
number

• When one of F0 to 255 (F0 to 2047 for AnA and AnU) is

turned on by SET F , F number, which has turned on, is
entered into D9125 to D9132 in due order in BIN code.

• F number, which has been turned off by RST F , is

erased from D9125 to D9132, and the contents of data
registers succeeding the data register, where the erased
F number was stored, are shifted to the preceding data
registers.

• By executing LEDR instruction, the contents of D9125

to D9132 are shifted upward by one. (With a CPU
equipped with an INDICATOR RESET switch, the same
process occurs when the switch is pressed.

• When there are 8 annunciator detections, the 9th one is

not stored into D9125 to 9132 even if detected.

SET
F50

SET
F25

SET
F99

RST
F25

SET
F15

SET
F70

SET
F65

SET
F38

SET

F110

SET

F151

SET

F210 LEDR

D9009

50 50 50 50 50 50 50 50 50 99

D9124

D9125

50 50 50 50 50 50 50 50 50 99

D9126

25 99 99 99 99 99 99 99 99 15

D9127

15 15 15 15 15 15 15 70

D9128

70 70 70 70 70 70 65

D9132

0 151 151 210

D9129

65 65 65 65 65 38

D9130

38 38 38 38 110

D9131

0 110 110 110 151

Usable with all

types of CPUs

D9133

D9134

D9135

D9136

D9137

D9138

D9139

D9140

Remote terminal
card information

00: No I/O module or

remote terminal
module or initial
communication
impossible

01: Input module or

remote terminal
module

10: Output module

• Stores information of I/O modules and remote terminal

modules connected to the A2C and A52G corresponding
to station number.

• Information of I/O modules and remote terminal modules

is for input, output and remote terminal module
identification and expressed as 2-bit data.
00: No I/O module or remote terminal module or initial

communication is impossible.

01: Input module or remote terminal module
10: Output module

• Data configuration

Station

D9133

D9140

b15 b14b13 b12b11 b10b9

b8b7

b6b5

b4b3

b2b1

Station

Usable with

A2C and

A52G

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 164 / 186

Результаты поиска

Содержание A1SH

Отзывы: