manualshive.com logo in svg

Mitsubishi A1SH, Руководство пользователя, Страница: 26 / 186

Поделиться
Скачать
Mitsubishi A1SH Скачать руководство пользователя страница 26

2. SYSTEM CONFIGURATION

2 - 8

MELSEC-A

2.2.2

Software packages

(1)

Specifying the system startup software package and startup model

(a)

For AnSHCPU, startup with the PLC model "A3."

(b)

Perform the PLC type setting as shown below when using conventional
peripheral devices.

CPU type

Peripheral

device

Software

package

A1SJH(S8)/

A1SH

A2SH

A2SH-S1

Remarks

SW[ ]IVD-GPPA *

MELSEC MEDOC

MELSEC MEDOC
plus

A3 *

A3

A3

IBM PC/AT

GX Developer

A1SJH/A1SH

A2SH

A2SH1

SW3GP-GPPAEE

EPROM write not possible.

A6PHP

SW4GP-GPPAEE

*

SW3-GPPAEE

SW3GP-GPPAEE

EPROM write not possible.

A6GPP

SW4GP-GPPAEE

A3 *

A3

A3

*

*

Selected model names differ as shown below, depending on the version of the software package:

Type

For ROM writing

For programming

Model name

Select "A0J2H"

Select "A1S"

Select "A1SH"

Select "A3"

Select "A1SH"

SW4GP-GPPA

Q or earlier

R or later

All versions

SW3RXV-GPPA

30D or earlier

40E or later

30D or earlier

40E or later

SW3NX-GPPA

60G or earlier

70H or later

60G or earlier

70H or later

SW3IVD-GPPA

60G or earlier

70H or later

60G or earlier

70H or later

POINT

(1)

Take note that old software packages other than the SW3-GPPA, SW3-
HGPA, SW3GP-GPPA and SW4GP-GPPA cannot be used for system
startup software packages when the A6GPP/A6PHP is used.

(2)

Take caution when using a software version that selects "A0J2H" or
"A1S" for ROM writing, since the file register area of 8k points is reduced
to 4k points.
To measure this, use a software package for which A1SJH/A1SH can be
selected.

Содержание A1SH



























































































































































































Отзывы:

Нет отзывов