Mitsubishi A1SH Скачать руководство пользователя страница 147

Страница: 147 / 186

APPENDICES

APP - 13

MELSEC-A

Table 2.1

Special relay list (Continue)

Number

Name

Description

Details

Applicable CPU

M9081

Registration area
busy signal for
communication
request

OFF: Communication

request to remote
terminal modules
enabled

ON: Communication

request to remote
terminal modules
disabled

• Indication of communication enable/disable to

remote terminal modules connected to the MINI (S3)
link module, A2C or A52G.

—

Usable with AnA,

AnA, AnU, A2AS,

QCPU-A (A Mode)

A2C and A52G.

M9082

Final station
number
disagreement

OFF: Final station

number agreement

ON: Final station

number
disagreement

• Turned on when the final station number of the

remote terminal modules and remote I/O modules
connected to the A2C or A52G disagrees with the
total number of stations set in the initial setting.

• Turned off when the final station number agrees with

the total number of stations at STOP

RUN

—

Dedicated to A2C

and A52G.

M9084

Error check

OFF: Checks enabled
ON: Checks disabled

• Specify whether the following errors are to be

checked or not after the END instruction is
executed (to set END instruction processing time):
• Fuse blown
• I/O unit verify error
• Battery error

Unusable with An,

A2C and A3V.

M9086

BASIC program
RUN flag

OFF: A3M-BASIC stop
ON: A3M-BASIC run

• Turned on when the A3M-BASIC is in RUN state,

and turned off when it is in STOP state.

—

Dedicated to A3M

M9087

BASIC program
PAUSE flag

OFF: A3M-BASIC RUN

enable

ON: A3M-BASIC disable

• Specifies enable/disable of A3M-BASIC execution

when the A3MCPU is in PAUSE state.
OFF: A3M-BASIC is executed.
ON:

A3M-BASIC is not executed.

—

Dedicated to A3M.

M9090

Power supply
problem status
on the PC side

OFF: Normal
ON: Power off

• Turns on if the power to the PC side is shut off when

the external power supply is connected to the CPU
board.
It stays on even after the status becomes normal.

—

Dedicated to
A2USH board

M9091

Operation error
detail flag

OFF: No error
ON: Error

• Turned on when an operation error detail factor is

stored at D9091, and remains ON after normal state
is restored.

—

Usable with AnA,
A2AS, AnU and
QCPU-A (A Mode).

M9091

Microcomputer
subroutine call
error flag

OFF: No error
ON: Error

• Turned on when an error occurred at execution of the

microcomputer program package, and remains ON
after normal state is restored.

—

Unusable with AnA,
A2AS, AnU and
QCPU-A
(A Mode).

M9092

External power
supply problem
status

OFF: Normal
ON: Power off

• Turns on when the external power being supplied to

the CPU board is shut off.
It stays on even after the status becomes normal.

—

Dedicated to
A2USH board

M9092

Duplex power
supply overheat
error

OFF: Normal
ON: Overheat

• Turned on when overheat of a duplex power supply

module is detected.

—

Dedicated to A3V.

M9093

Duplex power
supply error

OFF: Normal
ON: Failure or AC power

supply down

• Turned on when a duplex power supply module

caused failure or the AC power supply is cut down.

—

Dedicated to A3V.

M9094

I/O change flag

OFF: Changed
ON: Not changed

• After the head address of the required I/O module is

set to D9094, switching M9094 on allows the I/O
module to be changed in online mode. (One module
is only allowed to be changed by one setting.)

• To be switched on in the program or peripheral

device test mode to change the module during CPU
RUN. To be switched on in peripheral device test
mode to change the module during CPU STOP.

• RUN/STOP mode must not be changed until I/O

module change is complete.

—

Usable with An,
AnN, AnA, AnU.

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 147 / 186

Результаты поиска

Содержание A1SH

Отзывы: