manualshive.com logo in svg

Mitsubishi A1SH, Руководство пользователя, Страница: 64 / 186

Поделиться
Скачать
Mitsubishi A1SH Скачать руководство пользователя страница 64

5. POWER SUPPLY MODULE

5 - 2

MELSEC-A

(2)

Performance specifications for the A1SJHCPU(S8) built-in power supply.

Table 5.2

Performance specifications for the A1SJHCPU(S8) built -in power
supply

Type

Item

A1SJHCPU(S8)

Input power supply

100-120 V AC
(85 to 132 V AC)
500-240 V AC
(170 to 264 V AC)

Input frequency

50/60 Hz  

±

 3 Hz

Input voltage distortion factor

Within 5 % (See Section 8.8)

Input maximum apparent power

100 V A

Rush current

20 A 8 msec or less

Rated output

5 V DC 3 A

Overcurrent protection *1

3.3 A or over

Overvoltage protection *2

Not provided

Efficiency

65 % or over

Power supply indication

POWER LED indicator

Terminal screw size

M3.5 

×

 8

Applicable solderless terminal

0.3 to 2 mm

2

Applicable solderless terminal

RAV 1.25-3.5, RAV 2-3.5

Allowable momentary power failure *3 20 msec or less (100 V AC or over)

POINT

*1 :

Overcurrent protection

The overcurrent protection device shuts off the 5V, 24 V DC circuit and
stops the system if the current flowing in the circuit exceeds the specified
value.
When this device is activated, the power supply module LED is switched
OFF or dimly lit. In this case, remove any cause of overcurrent and start
up the system.

*2 :

Overvoltage protection

The overvoltage protection device shuts off the 5 V DC circuit and stops
the system if 5.5 to 6.5 V voltage is applied to the circuit.
When this device is activated, the power supply module LED is switched
OFF. In this case, switch OFF, then ON the input power to restart the
system.
The power supply module must be changed if the system is not booted and
the LED remains OFF.

*3 :

Allowable momentary power failure time

This value indicates the momentary power failure time allowed for the
PLC CPU and varies according to the power supply module used with the
PLC CPU module.
The allowable momentary power failure time for a system in which an
A1S63P is used is defined that it starts when the primary power supply of
the 24 V DC stabilized power supply of the A1S63P is turned OFF and lasts
until the 24 V DC becomes less than the specified voltage (15.6 V DC)

±

10 %

  15 %

±

10 %

  15 %

Содержание A1SH



























































































































































































Отзывы:

Нет отзывов