Mitsubishi A1SH Скачать руководство пользователя страница 23

Страница: 23 / 186

2. SYSTEM CONFIGURATION

2 - 5

MELSEC-A

2.2

Cautions on Configuring a System

This section describes the hardware and software that can be used with the
AnSHCPU.

2.2.1

Hardware

(1)

I/O module

An A[ ]N or A[ ]A building-block type I/O module can be used by loading it to
the A5[ ]B/A6[ ]B extension base.

(2)

Special function module

(a)

An A[ ]N or A[ ]A special function module can be used by loading it to the
A5[ ]B/A6[ ]B extension base.

(b)

Limits are imposed on the number of the following special function
modules that can be loaded.

AD51H-S3

AJ71UC24

AJ71E71N-B5T

AJ71C23-S3

AJ61BT11 (Only when in the intelligent mode)

AJ71C22-S1

AJ71E71N-B2

AD22-S1

A1SD51S

A1SJ61BT11(Only when in the intelligent mode)

A1SJ71UC24-R2(PRF/R4)

A1SJ71E71N-B2

A1SD21-S1

A1SJ71E71N-B5T

A985GOT (Only when the bus connection is used.)

A975GOT (Only when the bus connection is used.)

A970GOT (Only when the bus connection is used.)

A960GOT (Only when the bus connection is used.)

A956WGOT (Only when the bus connection is used.)

A956GOT (Only when the bus connection is used.)

A951GOT

Up to 2

AI61(S1)

A1SI61

Only 1

AJ71AP21(S3)

AJ71AT21B

AJ71BR11

AJ71AR21

AJ71LP21(G)

AJ71LR21

A1SJ71AT21B

A1SJ71AP21(S3)

A1SJ71LP21

A1SJ71AR21

A1SJ71BR11

A1SJ71LR21

Only 1

AJ71PT32-S3 (Only when in the extension mode.)

AJ71T32-S3 (Only when in the extension mode.)

A1SJ71PT32-S3 (Only when in the extension mode.)

A1SJ71T32-S3 (Only when in the extension mode.)

Only one module
can be installed.

POINT

When the dedicated instruction for the
CC-Link is used, use the master
module with ("9707 B" or later), shown
right, inscribed in the DATE column of
the rated plate.

9707 B

MITSUBISHI ELECTRIC

DATE

CPU UNIT
MODEL

Date of manufacture

Function version

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 23 / 186

Результаты поиска

Содержание A1SH

Отзывы: