Mitsubishi A1SH Скачать руководство пользователя страница 160

Страница: 160 / 186

APPENDICES

APP - 26

MELSEC-A

Table 2.2

Special registers list (Continue)

Number

Name

Description

Details

Applicable CPU

D9076

Status of writing
to standard ROM

Stores the status of
writing
(enabled/disabled) to
the standard ROM

Stores the status of writing (enabled/disabled) to the
standard ROM.
Statuses of DIP switch 3 and M9073

0: SW3 is OFF, M9073 is OFF/ON
1: SW3 is ON, M9073 is OFF
2: SW3 is ON, M9073 is ON

—

Dedicated to
QCPU-A
(A Mode)

D9077

Sequence
accumulation
time
measurement

Accumulation time
setting

• Stores the accumulation time used by M9077.

Setting range: 1 to 255ms (Default: 5ms)

When the value other than 1 to 255 ms is designated,

the value in D9077 is reset to 0.

—

Dedicated to
QCPU-A
(A Mode)

Stores the number of remaining instructions
(RIRD/RIWT/RISEND/RIRCV) being executable
simultaneously at one scan.
(With QCUP-A or AnUCPU)

Number of remaining instructions being executable = 10
– Number of instructions executed simultaneously
(With AnSHCPU)
Number of remaining instructions being executable = 64
– Number of instructions executed simultaneously

6: This function is available with the CPU of the

following S/W versions or later.

CPU Type Name

Software Version

Q02CPU-A, Q02HCPU-A,

Q06HCPU-A

A1SJHCPU, A1SHCPU,

A2SHCPU

Available with all versions

A2UCPU (S1), A3UCPU,

A4UCPU

S/W version Q

(Manufactured in July, 1999)

A2USCPU (S1)

S/W version E

(Manufactured in July, 1999)

A2USHCPU-S1

S/W version L

(Manufactured in July, 1999)

D9080

Number of
executable CC-
Link dedicated
instructions

Stores the number of
remaining CC-Link
dedicated instructions
being executable

Can be used only
with AnU, A2US,
QCPU-A
(A Mode) or
AnSH

D9081

Number of
vacant
registration areas
for
communication
requests

0 to 32

• Stores the number of vacant registration areas for

communication requests executed to remote terminal
modules connected to MINI (S3) link module, A2C and
A52G.

—

Usable with AnA,
A2AS, QCPU-A
(A Mode), AnU,
A2C and A52G.

D9082

Final connected
station number

Final connected station
number

• Stores the final station number of remote I/O modules

and remote terminal modules connected to A2C and
A52G.

—

Usable with A2C
and A52G.

D9085

Time check time 1 s to 65535 s

• Sets the time check time of the data link instructions

( ZNRD , ZNWR ) for the MELSECNET/10.

• Setting range: 1 s to 65535 s (1 to 65535)
• Setting unit:

1 s

• Default value: 10 s (If 0 has been set, default 10 s is

applied)

—

Usable with AnU
and A2AS,
QCPU-A
(A Mode)

D9090

Microcomputer
subroutine input
data area head
device number

Depends on the micro-
computer program
package to be used.

• For details, refer to the manual of each microcomputer

program package.

Unusable with
AnA, A2AS,
QCPU-A (A
Mode) and AnU.

Instruction error

Instruction error detail
number

• Stores the detail code of cause of an instruction error.

—

Usable with AnA,
A2AS, QCPU-A
(A Mode),AnA
board and AnU.

D9091

Microcomputer
subroutine call
error code

Depends on the micro-
computer program
package to be used.

• For details, refer to the manual of each microcomputer

program package.

Unusable with
AnA, A2AS,
QCPU-A
(A Mode),AnA
board and AnU.

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 160 / 186

Результаты поиска

Содержание A1SH

Отзывы: