manualshive.com logo in svg

Mitsubishi A1SH, Руководство пользователя, Страница: 163 / 186

Поделиться
Скачать
Mitsubishi A1SH Скачать руководство пользователя страница 163

APPENDICES

APP - 29

MELSEC-A

Table 2.2

Special registers list (Continue)

Number

Name

Description

Details

Applicable CPU

1

D9116

1

D9117

1

D9118

1

D9119

1

D9120

1

D9121

1

D9122

1

D9123

I/O module verify
error

Bit pattern in units of 16
points of verify error
units

• When I/O modules, of which data are different from those

entered at power-on, have been detected, the I/O unit
numbers (in units of 16 points) are entered in bit pattern.
(Preset I/O unit numbers when parameter setting has
been performed.)

D9116

D9117

D9123

15 14

12 11

13

10 9 8

6 5 4 3 2 1 0

7

0 0

0

0

0 0 0

0 0 0 0 0 0

0

0

0 0

0

0

0

0 0 0 0 0 0 0

0

0

0

0

0 0 0

0 0 0

0 0 0

0

Indicates I/O module verify error.

0

0

0

0

1

XY

7E0

1

XY

180

1

XY

0

• I/O module verify check is executed also to remote I/O

station modules.
(If normal status is restored, clear is not performed.
Therefore, it is required to perform clear by user
program.)

Usable with all

types of CPUs

Only remote

I/O station

information is

valid for A2C.

1

D9116

I/O module
verification error

Bit pattern of
verification error
module

• When an I/O module different from the I/O module data

registered during power-on is detected, this register
indicates the bit pattern of the I/O module number.

0

0

b15

D9116

b8 b7 b6 b5 b4 b3 b2 b1

0 is fixed.

Indicates the module
for setting switch 0.

Indicates the module
for setting switch 1.

Indicates the module
for setting switch 2.

Indicates the module
for setting switch 3.

Indicates the module for setting 
switch 4 or the module for
extension base unit slot 0.

Indicates the module for setting 
switch 5 or the module for
extension base unit slot 1.

Indicates the module for setting 
switch 6 or the module for
extension base unit slot 2.

Indicates the module for setting switch 7 or 
the module for extension base unit slot 3.

b0

—

Dedicated to

A0J2H.

D9124

Annunciator
detection quantity

Annunciator detection
quantity

• When one of F0 to 255 (F0 to 2047 for AnA and AnU) is

turned on by  SET F  1 is added to the contents of
D9124. When  RST F  or  LEDR  instruction is executed,
1 is subtracted from the contents of D9124. (If the
INDICATOR RESET switch is provided to the CPU,
pressing the switch can execute the same processing.)

• Quantity, which has been turned on by  SET F  is stored

into D9124 in BIN code. The quantity turned on with

 SET F  is stored up to “8.”

Usable with all

types of CPUs.

Содержание A1SH



























































































































































































Отзывы:

Нет отзывов