Mitsubishi A1SH Скачать руководство пользователя страница 143

Страница: 143 / 186

APPENDICES

APP - 9

MELSEC-A

Table 2.1

Special relay list (Continue)

Number

Name

Description

Details

Applicable CPU

M9046

Sampling trace

OFF: Except during trace

ON: During trace

• Switched on during sampling trace.

Unusable with A1

and A1N.

M9047

Sampling trace

preparation

OFF: Sampling trace stop

ON: Sampling trace start

• Turn on M9047 to execute sampling trace.

Sampling trace is interrupted if M9047 is turned off.

Unusable with A1

and A1N.

M9048

RUN LED flicker

flag

ON: Flickers at

annunciator on.

OFF: No flicker at

annunciator on.

• Sets whether the RUN LED flickers or not when the

annunciator relay F

is turned on when the A0J2H

is used.

—

Usable with A0J2H.

M9048

Memory card

battery voltage

detection

OFF: Low voltage is not

detected.

ON: Low voltage is

detected.

• Turned ON when the drop in the battery voltage for

the memory card is detected. (Automatically turned

OFF when the voltage recovers to normal.)

—

Dedicated to

QCPU-A (A Mode)

M9049

Switching the

number of output

characters

OFF: Up to NUL code are

output.

ON: 16 characters are

output.

• When M9049 is off, up to NUL (00

) code are output.

• When M9049 is on, ASCII codes of 16 characters

are output.

Unusable with An,

A3V, A2C and

A52G

M9050

Operation result
storage memory
change contact
(for CHG
instruction)

OFF: Not changed
ON: Changed

• Switched on to exchange the operation result storage

memory data and the save area data.

—

Dedicated to A3

M9051

CHG instruction

execution disable

OFF: Enable
ON: Disable

• Switched on to disable the CHG instruction.
• Switched on when program transfer is requested and

automatically switched off when transfer is complete.

—

Usable with A3,
A3N, A3H, A3M,
A3V, A3A, A3U,
A4U, A73 and A3N
board

M9052

SEG instruction

switching

OFF: 7SEG display
ON: Partial refresh

• Switched on to execute the SEG instruction as a

partial refresh instruction.
Switched off to execute the SEG instruction as a
7SEG display instruction.

Unusable with An,
A3H, A3M, A3V,
AnA, AnU, A3V
and A3A board

M9053

EI / DI

instruction
switching

OFF: Sequence interrupt

control

ON: Link interrupt

control

• Switched on to execute the link refresh enable,

disable (EI, DI) instructions.

Unusable with An,
A3V and A3N
board

M9054

STEP RUN flag

OFF: Other than step run
ON: During step run

• Switched on when the RUN key switch is in STEP

RUN position.

Unusable with An,
AnS, AnSH, A1FX,
A2C, A0J2H, and
A52G

M9055

Status latch
complete flag

OFF: Not complete
ON: Complete

• Turned on when status latch is completed. Turned off

by reset instruction.

Unusable with A1
and A1N.

M9056

Main program
P, I set request

OFF: Other than P, I set

request

ON: P, I set request

M9057

Subprogram 1
P, I set request

—

Usable with A3,
A3N, A3H, A3M,
A3V, A3A, A73,
A3U, A4U and A3N
board

M9060

Subprogram 2
P, I set request

M9061

Subprogram 3
P, I set request

OFF: Except during P, I

set request

ON: During P, I set

request

• Provides P, I set request after transfer of the other

program (for example subprogram when main
program is being run) is complete during run.
Automatically switched off when P, I setting is
complete.

—

Dedicated to A4U

Содержание A1SH



























































































































































































Результаты поиска

Содержание A1SH

Отзывы:

Mitsubishi A1SH, Руководство пользователя, Страница: 143 / 186

Результаты поиска

Содержание A1SH

Отзывы: