LABORIE Nexam Pro CIM Скачать руководство пользователя

Страница: 67 / 278

Urodynamic Catheters & Transducers Nexam Pro User Manual

Figure 3.13

Measuring Pves and Pabd

The procedure is as follows:

▪

Put the DT-XX pressure transducers in the holder and connect the

transducers to the CIM module.

▪

Place the pressure transducer holder at symphysis pubis level.

▪

Disinfect the genital area.

▪

Insert the bladder catheter and connect the catheter to the pressure

transducer P1 (P

ves

). Fix the catheter.

▪

Insert the rectal catheter and connect the catheter to the pressure

transducer P2 (P

abd

). Fix the catheter.

▪

Flush and zero the pressure transducers and catheters (see § 3.6.5).

▪

Ask the patient to cough to check the registration of all pressures.

▪

Start the investigation (cystometry or pressure-flow study, see chapters 5

and 6).

3.6.3

Measuring Pves, Pura and Pabd

Figure 3.14 shows the catheter setup for three pressures: P

ves

, P

ura

, and P

abd

This catheter can be used for cystometry, pressure-flow studies, UPP, and

gynecology studies.

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды