LABORIE Nexam Pro CIM Скачать руководство пользователя

Страница: 84 / 278

Nexam Pro User Manual

Pressure-Flow Study

6.1

Introduction

The pressure-flow study consists of two phases:

•

Filling phase (cystometry).

•

Voiding phase (uroflow).

During the filling phase, the pressure/volume relationship of the bladder is
measured. The filling phase is used to assess detrusor activity, bladder

sensation, capacity, and compliance. The voiding phase registers the miction
flow and voided volume during micturition.

6.2

Channels

The following channels can be measured during a pressure-flow study:

•

Vesical pressure

ves

(P1)

•

Abdominal pressure

abd

(P2)

•

Urethral pressure

ura

(P3)

•

Detrusor pressure

det

(P1-P2) (calculated)

•

Closure pressure

clos

(P3-P1) (calculated)

•

Conductance

Cond

•

Infused volume

•

EMG

•

Miction volume

mic

•

Miction flow

ura

During a pressure-flow study the patient should be awake, un-anaesthetized,
and neither sedated nor taking drugs that affect bladder function. Any

variations should be specified.

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды