LABORIE Nexam Pro CIM Скачать руководство пользователя | Manualshive

Страница: 249 / 278

background image

Safety Information

Nexam Pro User Manual

249

CAUTION

Remove the batteries when the flowsensor is not used for a

longer period (more than three months).

CAUTION

Do not use chloride-based solutions for cleaning the flow
stand. Check that the solution does not affect stainless

steel (AISI304L). Clean the flow stand if it was
contaminated with urine.

NOTE

Environmental conditions (i.e., thick walls/doors, iron in

walls/doors) may compromise the Bluetooth connection of
the flowsensor and battery lifetime.

Wireless (Bluetooth) puller (Mk III)

The Bluetooth puller complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This device

contains FCC-ID POOWML-C40XX.

WARNING

Make sure that the Bluetooth puller is connected to the
correct power adapter (PS-BT-PULLER). Do not use a

power adapter other than that which is specified. Doing
so may cause fire leading to serious damage.

WARNING

When adjusting the spring balanced arm be aware not to

pinch fingers or other objects.

WARNING

Connect the power adapter whenever the Bluetooth
puller is not used to prevent batteries to become

depleted. Deep discharging the batteries will damage the
batteries internally and shorten the lifespan.

WARNING

If the slider does not move smoothly (ticking noises)

during an investigation, the results are not reliable. Solve
the problem and redo the investigation.

«
...
247
248
249
250
251
...
»

Содержание Nexam Pro CIM























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Nexam Pro CIM

Бренд: Labnet Страницы: 5

Бренд: NANLUX Страницы: 39

Бренд: Tascam Страницы: 8

Бренд: Maico Страницы: 55

Бренд: Maico Страницы: 38

Бренд: Maico Страницы: 2

Бренд: MAHA Maschinenbau Haldenwang Страницы: 13

Бренд: Vatech Страницы: 137

Бренд: Vatech Страницы: 68

Бренд: Varytec Страницы: 52

Бренд: ZOLL Страницы: 48

Бренд: Park House Healthcare Страницы: 32

Бренд: Qlight Страницы: 4

SpinVessel VP 418SV3-1-850RB-CC

Бренд: V&P Scientific Страницы: 9

MACDON C HARVESTEC 6000

Бренд: CORN Страницы: 24

Бренд: Star Страницы: 16

Бренд: Ignis Pixel Страницы: 4

Бренд: Faro Страницы: 161

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды