LABORIE Nexam Pro CIM Скачать руководство пользователя страница 20

Страница: 20 / 278

Nexam Pro User Manual

Investigation Procedure

2.1 Introduction

The information in this chapter can be seen as a quick start to perform

urodynamic investigations. Besides software instructions, you will find
instructions for pump tube installation, positioning EMG electrodes, and

preparing the flowmeter and the catheter puller.

Detailed information about preparing the catheters and transducers can be
found in Chapter 3. The chapters 4 to 8

explain the specific urodynamic

investigations. Chapters 9 and 10 explain anorectal manometry and
biofeedback. Chapter 11 explains the Luna module and the procedure to

switch from stationary to ambulatory measurement.

The investigation procedure can be as follows:

▪

Start the LABORIE database program.

▪

Enter and select the patient.

▪

Start the measurement program.

▪

Prepare the investigation (pre-test).

▪

Run quality check.

▪

Perform the investigation.

▪

Print the investigation report.

▪

Clean system and catheters.

▪

Exit the LABORIE database program.

Detailed information about the database program and the reporter program
can be found in separate manuals in PDF format, which can be opened via the

Manuals

menu in the database program.

Detailed information about the measurement program and analysis program
can be found in the chapters 12 and 13.

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды