LABORIE Nexam Pro CIM Скачать руководство пользователя

Страница: 243 / 278

Safety Information

Nexam Pro User Manual

243

60601 system requirements should be applied prior to

use.

WARNING

Do not use High-Frequency (HF) surgical equipment on
the patient or in the vicinity of the Nexam Pro system as

the patient may experience burns. Device is not
intended for use with HF surgical equipment.

WARNING

Do not place the safety module/Multiple

Socket-Outlet (MSO) on the floor.

WARNING

Do not connect an additional Multiple Socket-
Outlet (MSO) or extension cord to the Nexam

Pro system.

WARNING

Do not connect non-ME equipment that is
supplied as part of this system intended to be

plugged into the Separating transformer
module into a wall outlet. The Separating

transformer is a safety component designed to
ensure Touch/Enclosure Leakage currents are

below the allowable limits. Operator may
experience electrical shock if non-ME

equipment is connected directly to the wall
outlet.

WARNING

Only connect equipment that has been

supplied as part of the Nexam Pro system to
the Multiple Socket Outlet provided on the

Separating transformer.

CAUTION

The digital MMS-bus cables connected to the Nexam
Pro modules all have a connector with locking

mechanism. Do not attempt disconnection by pulling the
cable. Loosen the lock by pressing the lever on the

connector.

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды