LABORIE Nexam Pro CIM Скачать руководство пользователя страница 64

Страница: 64 / 278

Nexam Pro User Manual

Chapter 3

▪

Insert the abdominal catheter in the rectum or the vagina.

▪

Remove the cap from the abdominal catheter. Be sure that no moisture is

getting into the catheter.

▪

Connect the abdominal catheter to the blue (P

abd

) pressure transducer

(tighten securely!). Be sure to connect in the OPEN position.

▪

Let the patient cough to get any of the access air out before charging the

catheters.

Figure 3.8

Connect catheter to pressure transducer in OPEN position

▪

Press the

Zero

all

button to zero all pressures to atmospheric pressure.

▪

Charge the catheters.

Figure 3.9

Charge catheters

▪

Fix the abdominal catheter.

▪

Withdraw the catheter and locate the urethral pressure sensor (P

ura

) at the

maximum urethral pressure (not for UPP).

▪

Ask the patient to cough to check the registration of all pressures. The

spikes of P

ves

abd

, and P

ura

should rise equally in response to the cough

and the detrusor pressure (P

det

) should remain relatively flat.

▪

Fix the bladder catheter (not for UPP).

▪

Start the investigation (cystometry, pressure-flow study, UPP, or

gynecology study, see chapters 5 to 8).

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды