LABORIE Nexam Pro CIM Скачать руководство пользователя страница 35

Страница: 35 / 278

Investigation Procedure

Nexam Pro User Manual

Figure 2.15

Pump tube pulled all the way down

▪

While placing the pump tube, note the following:

1. For correct functioning of the pump, it is essential that the pump tube is

inserted on both sides of the pump head into the V-shaped grooves

and pulled

all the way down

into the round openings.

Make sure that the pump tube is positioned according to the rotation

direction of the pump. The rotation direction of the pump is visible on
the control panel of the pump and can be set (clockwise or

counterclockwise) in the diagnostic program (see the

Nexam Pro

Service & Installation Manual

, document code MAN-00031).

▪

Place the tube clamp; do not stretch the tube while placing the clamp.

▪

Turn the lever back.

▪

Press the

Flush

button [6] on the pump to expel any air from the tube.

▪

Connect the pump tube to the filling lumen of the catheter.

▪

Start the investigation. The pump tube should not touch the saline bag

during the filling phase.

NOTE

For correct functioning of the pump, it is essential that the
pump tube is inserted on both sides of the pump head

into the V-shaped grooves and pulled

all the way down

into the round openings.

Pump tube pulled down in round opening

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды