LABORIE Nexam Pro CIM Скачать руководство пользователя

Страница: 75 / 278

Uroflowmetry

Nexam Pro User Manual

The letters between square brackets in the formulas refer to the corresponding
letters in Figure 4.2.

Void

The voiding function is reported as expressed by maximum flowrate together
with voided volume and post-void residual urine in the format:

VOID = Qmax/VV/VRU (Maximum flow/Volume Voided/Residual Volume)
Undetermined values are substituted by a hyphen -. when only the volume is

measured VOID = -/340/-.

Qmax

Qmax is the maximum measured value of the flow during micturition.

When a is present, the Qmax will be the flow at the Peak flow marker. When
no Peak flow marker is present and Flow markers are present, the peak flow

will be the flow at the second Flow marker.

Calculated: Qmax = [F]

Time to Qmax

The time to Qmax is the elapsed time from the onset of the flow to the Qmax.

Calculated: Time to Qmax = [C]

Voided volume

The voided volume is the total volume expelled via the urethra.

Calculated: Voided volume = [E1+E2+E3+E4]

Flow time

The flow time is the time over which measurable flow actually occurs.

Calculated: Flow time = [B1+B2+B3+B4]

Voiding time

The voiding time is the total duration of micturition, including the miction
interruptions. When voiding is completed without interruptions, voiding time is

equal to flow time.

Calculated: Voiding time = [D]

Hesitancy

The hesitancy is the time from the moment the investigation is started until the

patient started voiding.

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды