LABORIE Nexam Pro CIM Скачать руководство пользователя

Страница: 113 / 278

Anorectal Manometry

Nexam Pro User Manual

113

9.2.2

Select the Catheter

Anorectal manometry investigations can be performed by either using (a)
water catheters with DT-NN pressure transducers, (b) air-charged catheters

with external pressure transducers or (c) solid state catheters. LABORIE
advises to use catheters with 4 pressure channels for the most accurate

results.

The layout of the two most common 4-channel catheters is displayed in

Figures 9.2 and 9.3:

•

one cm spacing between the four pressure channels (spiral) and a balloon

at the tip in order to test the anorectal reflex (RAIR) and sensations.

•

four pressure channels at the same location (radial) with an angle of 90

degrees and a balloon at the tip in order to test the anorectal reflex (RAIR)

and sensations.

Figure 9.2

Anorectal manometry catheter, spiral

Figure 9.3

Anorectal manometry catheter, radial

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды