LABORIE Nexam Pro CIM Скачать руководство пользователя страница 148

Страница: 148 / 278

148

Nexam Pro User Manual

Chapter 9

9.5.3

Anorectal Manometry Settings

During analysis, you can define how certain results should be calculated. This
can be done in the anorectal manometry settings window, which can be

activated by

Settings > Anorectal manometry settings

. These anorectal

settings are stored with the investigation. This means that changes made here

are in effect only for the current study.

Figure 9.24

Anorectal manometry settings

Squeeze/Cough results

The squeeze and cough results are calculated either on channels that are
defined as EAS in the channel definition (

Settings > Channel definition

) or

on certain user-selectable channels. To select the channels yourself, click the
button with

“

…

”; a selection window will display. Just check the channel you

would like to include for the results.

Anal profile results

The (rest and squeeze) profile results are calculated either on channels that
are defined as

Anal

in the channel definition (

Settings > Channel definition)

or on certain user-selectable channels. To select the channels yourself, click
the button with

“

…

”; a selection window will display. Just check the channel

you would like to include for the results.

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды