LABORIE Nexam Pro CIM Скачать руководство пользователя | Manualshive

Страница: 136 / 278

background image

136

Nexam Pro User Manual

Chapter 9

Filling with air (Perfusion Pump Plus)

Press the

Next test

button until the text ‘No sensation’ is displayed on

the left button. Connect the filling lumen of the catheter to the perfusion

pump.

Press the

Start filling

button to inflate the balloon with air according to

the volume displayed on the button (default 250 ml; you can change

the initial volume by using the arrow buttons). You can find an
indication of the infused volume on the status bar at the bottom of the

screen.

Press this button when a patient (during infusion) states a certain

sensation. A balloon marker and sensation marker is inserted. The

sensation markers are defined in the protocol settings: No sensation,
First sensation, First urge, Modest urge, Intense urge, Maximum

tolerable volume, and Pain. When the maximum tolerable volume is
reached, stop inflating the balloon by clicking the

Inflate balloon

button again.

Press the

Stop filling

button to stop filling.

During the filling, in case the volume which is displayed on the button is
reached, the pump automatically stops and the button shows a new volume

which can be reached. If you start filling again, the balloon will be filled until the
new volume, which is displayed on the button. When the maximum filling for

the catheter has been reached, the pump automatically stops and the balloon
cannot be filled more. The maximum balloon filling is predefined in the catheter

definition.

Press the

Deflate balloon

button to deflate the balloon.

After deflating, the button will show

Start filling

again.

Press the

Next test

button to continue with the next test. The balloon

will be deflated automatically.

«
...
134
135
136
137
138
...
»

Содержание Nexam Pro CIM























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Nexam Pro CIM

Бренд: Campbell Страницы: 18

Бренд: Vector Страницы: 4

Бренд: Unex Страницы: 5

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

Бренд: Rangevision Страницы: 28

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: Hagerman Страницы: 4

Бренд: hager Страницы: 2

TECSHOW QUAD SPIDER 60

Бренд: Ampro Страницы: 9

Бренд: iHealth Страницы: 8

Бренд: Madrigal Страницы: 5

Бренд: MacDon Страницы: 504

Бренд: Madsen Страницы: 206

Бренд: Nautilus Страницы: 17

Бренд: National Instruments Страницы: 6

Бренд: P-Q Controls Страницы: 5

Бренд: P+L Systems Страницы: 2

Бренд: PacBio Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды