LABORIE Nexam Pro CIM Скачать руководство пользователя

Страница: 264 / 278

264

Nexam Pro User Manual

Appendix C

Message

Cause

Posible actions to
resolve

DT-XX transducer not connected to CO2 module Transducer expected but not

connected

Contact your LABORIE
representative

Due to a change in the channel configuration
some approved events might have been set to
not approved. It is advised to re-analyse these
events

Events problem

Re-analyse events

Error during backup [Filename]

N/A

Contact your LABORIE
representative

Error during saving test data!

General error during saving test
data

Contact your LABORIE
representative

Error during saving test data! Investigation
number > 99

Investigation number > 99

Contact your LABORIE
representative

Error during saving test data! Not enough
memory available. Cannot perform
investigation.

Not enough memory available

Contact your LABORIE
representative

Error in writing to file: [Filename]

Error during save to demo file

Retry save as demo file

Error while allocating MPEG4 buffers!

MPEG4 buffer problem

Contact your LABORIE
representative

Error while allocating video buffers. Increase the
non-paged memory size in Milconfig.

Error while allocating video
buffers

Increase the non-paged
memory size in
Milconfig

Fatal error during reading of the testdata!

Exception during reading test data Contact your LABORIE

representative

Fatal error occurred during the measurement!

Exception during measurement

Contact your LABORIE
representative

Flowmeter not connected!

Module expected but not
connected

Contact your LABORIE
representative

Flowmeter not connected! The LABORIE-bus
devices can only be used when the following
criteria are met: The Solar Blue is powered via
the power adapter. The Solar Blue is connected
to the computer via USB.

Module expected but not
connected

Contact your LABORIE
representative

Illegal use of LABORIE software on a network

Application cannot be started
from network location

Start application from
LABORIE database

Incorrect serial port selected. Blood pressure
recording not possible. Change serial port
settings and restart the test.

Incorrect serial port selected

Change serial port and
restart test

Invalid character encountered - use only hex
digits 0

…

9, A

…

Invalid character in catheter string
to decode

Contact your LABORIE
representative

Luna Cond not present

Luna channel expected but not
present

Contact your LABORIE
representative

Luna connection lost.

Communication problems

Contact your LABORIE
representative

Luna EMG not present

Luna channel expected but not
present

Contact your LABORIE
representative

Luna P1 not present

Luna channel expected but not
present

Contact your LABORIE
representative

Luna P2 not present

Luna channel expected but not
present

Contact your LABORIE
representative

Luna P3 not present

Luna channel expected but not
present

Contact your LABORIE
representative

MEMORY FULL **** DATA IS NOT SAVED NOW! Memory full, Investigation took

longer than expected

Stop the investigation
and start a new
investigation if
applicable

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды